User manual FUJITSU SIEMENS SCENIC T (VIA)

[. . . ] any technical problems or other questions you need clarified?Please contact: · your sales partner · your sales outlet You will find further information in the manual "Safety, Guarantee and Ergonomics". The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. [. . . ] Text in italics indicates commands or menu items. "Quotation marks" indicate names of chapters or terms. Important notes Store this manual close to the device. If you pass the device on to third parties, you should pass this manual on with it. Be sure to read this page carefully and note the information before you open the device. You cannot access the system board components without first opening the device. How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please observe the safety information provided in the "Important notes" chapter in the device's operating manual. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-on modules" - "Replacing the lithium battery" section. ! A26361-D1322-Z120-1-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device. Real-time clock/calendar with integrated battery backup 1 internal WOL interface 2 internal USB ports (C / D) 1 external parallel port (ECP- and EPP-compatible) 2 external serial ports (16C550 compatible with FIFO) 2 external PS/2 ports for keyboard and mouse 2 external USB ports (A / B) · · · · · · · · · External ports 13 4 5 6 8 2 7 9a 9b9c 1= 2= 3= 4= 5= 6= 7= PS/2 mouse port PS/2 keyboard port Serial port 1 Parallel port Serial port 2 LAN connector USB ports A and B 8 = Game/Midi port 9a = Audio Line-Out Headphones 9b = Audio Line-In 9c = Audio Micro-In The components and connectors marked are not necessarily present on the system board. 4 - English A26361-D1322-Z120-1-7419 Features Internal ports and connectors 1 234 5 6 7 8 9 DIMM 3 DIMM 2 DIMM 1 15 AGP 10 11 PCI 1 14 1= 2= 3= 4= 5= 6= 7= 8= 9= Power supply ATX Floppy Disk Drive IDE drives 3 and 4 (secondary) Power supply monitoring Connector for control panel and loudspeaker IDE drives 1 and 2 (primary) Voltage indicator LED Fan 2 Cover monitoring 13 PCI 2 12 10 = USB ports C / D * 11 = Wake On LAN 12 = CD audio input 13 = AUX audio input 14 = Power supply +12 V 15 = Fan 1 (e. g. for the processor) The components and connectors marked are not necessarily present on the system board. PCI 3 A26361-D1322-Z120-1-7419 English - 5 Features Temperature / System monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damage caused by overheating. In addition, any unnecessary noise is also prevented by reducing the fan speed, and information is provided about the system status. Cover monitoring protects the system from unauthorised opening. An onboard controller developed by Fujitsu Siemens Computers controls the temperature and system monitoring. The following functions are supported: Temperature monitoring: Measurement of the processor and the system temperature with an onboard temperature sensor. Temperature control: The temperature is controlled by adjusting the fan speed and/or by reducing the clock frequency of the processor. The clock frequency of the processor is dependent upon the setting in the BIOS Setup. Temperature-dependent processor speed control enables a reduced fan speed, decreasing noise. Fan monitoring: Fans which have been removed, blocked or sticky fans are detected. Blocked or sticky fans are operated with 12 V pulse voltage. [. . . ] memory modules, AGP and PCI extension boards) are still supplied with power. The voltage indicator LED will glow if this is the case. All PCI slots support 3. 3 V main and auxiliary voltages. AGP boards support 1, 5 V main and auxiliary voltages. 5 4 3 2 DIMM 3 DIMM 2 DIMM 1 AGP PCI 1 1 7 1= 2= 3= 4= Socket for processor with heat sink Location bank 1 for main memory Location bank 2 for main memory Location bank 3 for main memory 6 5 = Lithium battery 6 = PCI slots 1, 2, 3 7 = AGP slot PCI 2 PCI 3 A26361-D1322-Z120-1-7419 English - 9 Add-on modules Installing and removing processors 3 2 4 5 1 A Ê Ê Ê Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). [. . . ]