User manual FUJITSU A6010

[. . . ] fennec. book Page 1 Thursday, September 7, 2006 11:42 AM Fujitsu LifeBook A6010 Notebook ® User's Guide fennec. book Page 2 Thursday, September 7, 2006 11:42 AM fennec. book Page 3 Thursday, September 7, 2006 11:42 AM Copyright Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. MS, MS-DOS, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. [. . . ] You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your notebook. This battery has an expected life of 2 to 3 years. System BIOS shadowed System BIOS copied to shadow RAM. *System CMOS checksum bad ­ run SETUP BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in BIOS memory. *System RAM Failed at offset: nnnn System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs. 56 nnnn System RAM Passed Where nnnn is the amount of system memory in kilobytes successfully tested. *System timer error The timer test failed. The main clock that operates the computer is faulty. Contact your support representative for repairs. UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager. Video BIOS shadowed Video BIOS successfully copied to shadow RAM. EMERGENCY MEDIA PLAYER DRIVE TRAY RELEASE If for some reason the eject button fails, you can open the DVD/CD-ROM tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out a short distance. MODEM RESULT CODES The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are: OK NO CARRIER NO DIALTONE CONNECT 53000 (Connection complete at 53, 000 bps. ) ERROR FAX RING (This means an incoming call. ) BUSY NO ANSWER When using the internal modem with applications that are not factory installed refer to the application documentation. fennec. book Page 57 Thursday, September 7, 2006 11:42 AM Troubleshooting RESTORING YOUR PRE-INSTALLED SOFTWARE The Drivers and Applications Restore (DAR) disc contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your computer configuration for use as documented below. In order to install applications and/or drivers from the DAR disc, you will need to use an optical drive either in your system or attached externally. 5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system. RESTORING THE FACTORY IMAGE The Restore Disc that came with your system contains two utilities: If you have access to the internet, visit the Fujitsu website at: http://www. us. fujitsu. com/computers to check for the most current information, drivers and hints on how to perform recovery and system updates. The Recovery utility allows you to restore the original contents of the C: drive. The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. [. . . ] Select the fingerprint recognition device in the Select Authentication Device screen (it should already be marked by a green check if you have a finger enrolled) and click Next. System Settings The OmniPass Startup Options interface can be found in the System Settings tab. With these options you can specify how your OmniPass Logon is tied to your Windows Logon. The first option, Automatically log on to OmniPass as the current user, will do just as it says; during Windows login, you will be logged on to OmniPass using your Windows login credentials. [. . . ]