User manual FUJITSU ASYA24LCCINSTALL

[. . . ] 3 PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ADJUSTING THE DIRECTION OF AIR CIRCULATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 SWING OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This function is especially convenient when you want to remove the humidity in the room without significantly lowering the room temperature. During ECONOMY operation, the thermostat setting automatically changes according to the temperature to avoid Unnecessary cooling and heating for the most economical operation. If the room is not cooled(or heated) well during economy operation, select normal operation. Once air conditioner operation is stopped, normal operation begins when the indoor unit is turned on again. During the monitor period in the AUTO mode, the air conditioner operation will not change to ECONOMY operation even if ECONOMY operation is selected by pressing the ECONOMY operation button. HI-POWER OPERATION Begin Air Conditioner operation before performing this procedure. Open the Remote Control Unit lid. To Use the HI-POWER Operation Press the HI-POWER button(Fig. 5 c). The Indoor Unit's HI-POWER Indicator Lamp (orange) (Fig. 2 8) will light. HI-POWER operation begins. To Stop the HI-POWER Operation Press the HI-POWER button(Fig. 5 c) again. The Indoor Unit's HI-POWER Indicator Lamp(orange) (Fig. 2 8) will go out. However, HI-POWER operation will automatically stop under the following conditions. If SUPER QUIET Operations are selected during HI-POWER Operation, HI-POWER will be cancelled. During cooling mode The room temperature is 1°C below the thermostat setting or 30 minutes has passed since the HI-POWER operation began. During heating mode The room temperature is 2°C above the thermostat setting. At this time, the dust on the air filters is collected in the dust boxes (behind the open panel). Open panel 2. Air filter retract After the air filters come out, they automatically retract to their original positions in the Indoor Unit. When the auto filter maintenance is complete, the MAINTENANCE SIGN Indicator Lamp (red) (Fig. 2 4) on the Indoor Unit goes out. MAINTENANCE SIGN Indicator Lamp(red) flashes The MAINTENANCE SIGN Indicator Lamp (Fig. 2 4) will flash during auto filter maintenance if the air filters are not Installed or are pulled. If this occurs during air conditioner operation, unplug the power supply cord from the Electrical outlet and follow procedures "Dust Box Maintenance" to install the air filters. Changing the FILTER MAINTENANCE Interval The filter maintenance interval can be changed. Some dust may be tough to clear away with Auto Filter Maintenance. In such a situation, please switch the Interval to 50H for more thorough cleaning. While cleaning, please place the remote control in stop mode (so that only the CLOCK and the time are displayed). Hold down the SET TIME button (Fig. 5 l) for at least 3 seconds. Switches from displaying the current time to displaying the interval, and begins blinking. Set the interval using the SET TIME button's and keys (Fig. 5 l). Pressing these buttons will allow you to scroll between the figures below. For more detailed FILTER MAINTENANCE, set to 50H. [. . . ] Air the air conditioner's intake grille or outlet port blocked?Poor Cooling performance: Did you adjust the room temperature settings (thermostat) correctly? In the case of Cooling operation, is a window allowing bright sunlight to enter?(Close the curtains. ) In the case of Cooling operation, are there heating apparatus and computers inside the room, or are there too many people in the room? [. . . ]