User manual FUJITSU LIFEBOOK P1610

[. . . ] P Series. book Page 1 Monday, October 9, 2006 10:58 AM Fujitsu LifeBook P1610 Notebook ® User's Guide P Series. book Page 2 Monday, October 9, 2006 10:58 AM P Series. book Page 3 Monday, October 9, 2006 10:58 AM Copyright Copyright & Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes. Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited. [. . . ] UMB upper limit segment address: nnnn Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager. Video BIOS shadowed Video BIOS successfully copied to shadow RAM. MODEM RESULT CODES The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes. Examples of result codes are: OK NO CARRIER NO DIALTONE CONNECT 53000 (Connection complete at 53, 000 bps. ) ERROR FAX RING (This means an incoming call. ) BUSY NO ANSWER When using the internal modem with applications that are not factory installed refer to the application documentation. 59 P Series. book Page 60 Monday, October 9, 2006 10:58 AM L eBook P 600 N es bot k o Se L iiffe B o o k P 1 S e r i eSse r i o t e N o o e b - o k c t i o n F i v e Restoring Your Pre-installed Software The Drivers and Applications Restore (DAR) CD contains sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your notebook configuration for use as documented below. If you have access to the internet, visit the Fujitsu Support website at http:// www. computers. us. fujitsu. com/support to check for the most current information, drivers and hints on how to perform recovery and system updates. See "Automatically Downloading Driver Updates" on page 61. 5. Once you have selected the components you wish to install, click [Install Selected Subsystems]; the components will be installed. After the components are installed, click [OK], then click [Yes] when asked if you want to reboot the system. RESTORING THE FACTORY IMAGE The Restore Disc that came with your system contains two utilities: The Recovery utility allows you to restore the original contents of the C: drive. The Hard Disk Data Delete utility on this disc is used to delete all data on your hard disk and prevent it from being reused. Do not use the Hard Disk Data Delete utility unless you are absolutely certain that you want to erase your entire hard disk, including all partitions. · The use of this disc requires that you have a device capable of reading CDs attached to your system. If you do not have a built-in CD player, you will need to attach an external player. For more information on available external devices, visit our website at: www. shopfujitsu. com. · This disc can only be used with the system with which it was purchased. Re-Installing Individual Drivers and Applications The Drivers and Applications CD can be used to selectively re-install drivers and/or applications that may have been un-installed or corrupted. There may be certain free third-party applications pre-installed on your system that are not on the DAR CD. The latest versions of the applications can be downloaded from the third-party's website. To re-install drivers and/or applications: 1. Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Installer screen is displayed after the CD is inserted. After reading the License Agreement, click [I agree]. A window will appear containing a list of applications, drivers, and utilities that you can install from the Drivers and Applications CD. The components listed are color-coded in terms of their install status. Blue indicates that the component can be installed. Green indicates that the component needs to be installed separately. Grey indicates a component that is already installed; grey items can be reinstalled, but prior to installation you will receive a reminder that the component is already installed. BOOT Priority Change Before restoring an image, you must first verify that your system is set up to boot from the CD drive. [. . . ] You authenticate with OmniPass (via master password, or an enrolled security device) and OmniPass logs you into Windows. You may, during this OmniPass authentication, see a Login Error dialog box. This dialog box occurs when OmniPass was unable to log you into Windows with the credentials supplied (username and password). This could happen for any of the following reasons: Your Windows password has changed Your Windows account has been disabled If you are having difficulties due to the first reason, you will need to update OmniPass with your changed Windows account password. [. . . ]