User manual FUNAI 4919CLT

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] · When you select [TV-Y7]: Press the STOP/L or PLAY/K button to select "FV" (Fantasy Violence). Then, press the F. FWD/B button to select [BLOCK] or [VIEW]. · When you select [TV-PG], [TV-14] or [TV-MA]: Press the STOP/L or PLAY/K button to select "D"(Suggestive Dialog), "L"(Coarse Language), "S"(Sexual Situation), or "V"(Violence). Then, press the F. FWD/B button to select [BLOCK] or [VIEW]. Note: When you select [TV-MA], "D" does not appear on the TV screen. · The sub-ratings which set to [BLOCK] appears next to the rating category in the TV RATING menu. TV­Y7 [BLOCK] B FV [BLOCK] TV­PG [BLOCK] BD L S V [BLOCK] [BLOCK] [BLOCK] [BLOCK] B TV­Y TV­Y7 ( ) TV­G TV­PG (DLSV ) TV­14 (DLSV ) TV­MA ( LSV ) [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] 3 Select your desired item G PG PG­13 BR NC­17 X [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] Press the PLAY/K or STOP/L button to point to your desired item. Then, press the F. FWD/B button to select [BLOCK] or [VIEW]. · When you select the rating cateSelection G PG PG-13 R NC-17 X Rating Category Explanations General Audience Parental Guidance suggested. Unsuitable for children under 13 Restricted; under 17 requires accompanying parent or adult guardian No one under 17 admitted Mature audience only · gory and turn it [BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn [VIEW] automatically. When you turn "G" to [VIEW], the all ratings will turn to [VIEW] automatically. 4 Exit the V-Chip setting mode Press the MENU button on the remote control to return to original mode. - 16 - EN 9I03 PLAYBACK This TV/VCR will operate with any cassette that has the mark. (in the LP / SLP modes only) NOTE: Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture may revert to Black and White. 3)Press the PLAY button to return to normal speed. NOTES: · Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time. · This function will not operate in recording mode. In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction. 1 2 Insert a tape. Select "TIME SEARCH" mode Press the TIME SEARCH button (with each push it will increase by 10 minute). 3 Enter your desired time ZERO RETURN This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding. NOTE: Zero Return WILL NOT work on a blank tape or a blank portion of a tape. Press the PLAY/K or STOP/L button until your desired time appears. (Example: "2:50" stands for 2 hours 50 minutes) If you wish to cancel the Time Search at this point, press the MENU button on the remote control. TIME SEARCH 2 : 50 4 Begin Time Search 1 Stop a tape at your desired point Rewind or fast forward the tape to the beginning point at which you want to review. By pressing the REW/s or F. FWD/B button, the TV/VCR will rewind or fast forward to the specified point. The time counts down as the searching progresses. When 0:00 is reached, the tape will start playback automatically. 2 3 Reset the counter to 0:00:00 Press the COUNTER RESET button repeatedly. Begin recording or playback TO CANCEL THE TIME SEARCH at this point Press the STOP/EJECT button on the TV/VCR or the remote control. This will delete the selected time. Press the RECORD or PLAY button. Press the STOP button when recording or playback is completed. STILL PICTURE 4 To activate "ZERO RETURN" mode Press the MENU button on the remote control. [. . . ] (Ejemplo: 40) 8) Pulse el botón MENU en el mando a distancia. Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa MENU en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta. - 31 - ES FUNAI CORPORATION LIMITED WARRANTY FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows: DURATION: PARTS: LABOR: FUNAI CORP. [. . . ]