User manual FUNAI CD100A

[. . . ] CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. LOCATION: INSIDE, NEAR THE DECK MECHANISM. FCC WARNING- This equipment may generate or use radio frequency energy. [. . . ] Then, press B. ­ 19 ­ EN 1L25 ¡If a tape ends during TIMER RECORDING, the 2) Set the frequency of the recording For once: Press K or L to point to "ONCE". For daily (Monday~Friday): Press K or L to point to "DAILY". For weekly: Press K or L to point to "WEEKLY". Then, press B. 3) Set the date PROGRAM NUMBER 4 ONCE DAILY WEEKLY First, press K or L for the month. Then, press B. 4) Set the start time ONE TIME PROGRAM PROGRAM NUMBER 4 DATE --/-START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - First, press K or L for the hour. Then, press B. 5) Set the end time ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /12 MON START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - - VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER REC light blinks. (If the DVD power is off, the VCR will become STANDBY status). ¡If a tape is not in the VCR or does not have a safety tab, the TIMER REC light flashes and timer recording will not operate. ¡When all timer recordings are finished, the TIMER REC light will flash. To use the VCR again as usual, press T-SET to disable the flashing TIMER REC light, then press VCR/TV to select the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual. (See "RF OUTPUT CHANNEL" on page 13 for the detail). Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording VCR] (this unit) DVD/VCR AUDIO OUT 2 Press VCR/TV on the recording VCR. VCR DVD S-VIDEO COMPONENT AUDIO VIDEO OUT OUT OUT Y DIGITAL AUDIO OUT ANT-IN L R ANT-OUT VIDEO OUT AUDIO IN Cb L COAXIAL VIDEO IN Cr R RF cable (supplied) [TV set] (Use for monitoring) Audio/Video cables (not supplied) OUT IN AUDIO VIDEO ANT in [Playing VCR] (another source) 1 Insert a pre-recorded tape into the playing VCR. 2 Insert a tape with a safety tab into the recording VCR. 3 Press SPEED on the recording VCR to select the desired recording speed (SP/SLP). 4 Select the "L1" or "L2"position on the recording VCR. ¡When you use the A/V input jacks on the back of the DVD/VCR, select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons (o/p). ¡When you use the A/V input jacks on the front of the DVD/VCR, select "L2" position by pressing [0], [0], [2] on the remote control or the CHANNEL buttons (o/p). 5 Press REC/OTR on the recording VCR. 6 Begin playback of the tape in the playing VCR. ¡For best results during dubbing, use the VCR's front panel controls whenever possible. The remote control might affect the playing VCR's operation. ¡Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended. [. . . ] En este caso, siga el paso [3]. 2 Seleccione "AJUSTE DE RELOJ" mediante el botón K ó L. Después, presione B. otro componente que esté conectado al DVD. ¡Asegúrese de que la televisión y el receptor de 3 Ajuste el reloj. 1) Ajuste el mes Presione el botón o ó p repetidamente. Entonces, presione B. 2) Ajuste el d a audio (disponible en los comercios) esté ajustado en el canal correcto. ¡Seleccione el modo DVD presionando el botón DVD que está situado en el mando a distancia o el botón output situado en el panel frontal. 1 Presione el botón POWER. [. . . ]