User manual FUNAI F05

[. . . ] 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. 5. Cleaning-Unplug TV/VCR from the wall outlet before cleaning. [. . . ] Note: When you select [TV-MA], "D" does not appear on the TV screen. · The sub-ratings which set to [BLOCK] appears next to the rating category in the TV RATING menu. TV­Y7 B FV TV­PG BD L S V B TV­Y TV­Y7 ( ) TV­G TV­PG (DLSV ) TV­14 (DLSV ) TV­MA ( LSV ) Press the PLAY/K or STOP/L button to point to "MPAA RATING". Then, press the F. FWD/B button. 3 Select your desired item G PG PG­13 BR NC­17 X [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] Press the PLAY/K or STOP/L button to point to your desired item. Then, press the F. FWD/B button to select [BLOCK] or [VIEW]. Selection G PG PG-13 R NC-17 X [BLOCK] [BLOCK] Rating Category Explanations General Audience Parental Guidance suggested. Unsuitable for children under 13 Restricted; under 17 requires accompanying parent or adult guardian No one under 17 admitted Mature audience only · When you select the rating category and turn it · [BLOCK] [BLOCK] [BLOCK] [BLOCK] [BLOCK] [BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn [VIEW] automatically. When you turn "G" to [VIEW], then all ratings will turn to [VIEW] automatically. Exit the V-Chip setting mode 4 Press the MENU button on the remote control to return to original mode. [VIEW] [VIEW] [VIEW] [BLOCK] [BLOCK] [BLOCK] - 16 - EN 01A11 FM MODE This function enables you to receive FM radio broadcasting. 1 Set the FM mode FM 88. 0 MHz Press the TV/FM button on the remote control. The radio frequency appears on the TV screen. 2 Select the radio frequency you want to receive Press the CHANNEL K or L button until your desired radio frequency appears. NOTES: · The radio frequency indication repeats to appear and disappear. · You can not record the FM radio wave broadcasting. · If you receive a weak radio signal, you may change the FM Antenna mode to INT(internal) or EXT(external) by following the step below. Then, press the F. FWD/B button. - 17 - EN 01A11 2 Select "ALL" or "BLANK" ­ USER'S SET UP ­ ZERO RETURN RENTAL B REPEAT PLAY AUTO RETURN [OFF] [ALL] [OFF] Press the PLAY/K or STOP/L button to point to "REPEAT PLAY". Press the F. FWD/B or REW/s button repeatedly until your desired selection [ALL] or [BLANK] appears. This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding. NOTE: Zero Return WILL NOT work on a blank tape or a blank portion of a tape. 3 Exit the Repeat Play setting 1 Stop a tape at your desired point Press the MENU button on the remote control to return to the TV mode. Rewind or fast forward the tape to the beginning point from which you want to review. 4 Start playback 2 3 Reset the counter to 0:00:00 Press the PLAY button to start the Repeat Play. · Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/VCR. · If the Rental mode is set [ON], the "RENTAL PLAY B" display has priority. Press the COUNTER RESET button repeatedly. Begin recording or playback Press the RECORD or PLAY button. Press the STOP button when recording or playback is completed. 4 TO CANCEL THE REPEAT PLAY MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. Press the MENU button on the remote control to return to TV mode. If there is a power failure of any kind, the unit will retain its memory for this feature. To activate "ZERO RETURN" mode Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "ZERO RETURN". The counter will appear on the TV screen. The tape will automatically stop when the counter returns to 0:00:00. ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] B ZERO RETURN TIME SEARCH SEARCH PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. [. . . ] (Ejemplo: 7 - 07) Luego, pulse el botón F. FWD/B. 5) Pulse el botón PLAY/K o STOP/L hasta que aparezca el año deseado. (Ejemplo: 2002) Luego, pulse el botón F. FWD/B. 6) Pulse el botón PLAY/K o STOP/L hasta que aparezca la hora deseada. [. . . ]