User manual FUNAI SC3919V

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] · Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/VCR. · If the Rental mode is set [ON], the "RENTAL PLAY B" display has priority. STOP 3 To stop playback Press the STOP button when playback is completed. TO CANCEL THE REPEAT PLAY MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. Press the MENU button on the remote control to return to TV mode. If there is a power failure of any kind, the unit will retain its memory for this feature. - 16 - EN 9J27 SEARCH PICTURE SEARCH This feature is very useful in finding or skipping over a particular scene on a tape. 1)You may view a video tape at a high speed in either a forward or reverse direction by pressing the F. FWD or REW button during playback. (in the SP / LP / SLP modes) 2)Press it again and the TV/VCR will now search in super high speed. (in the LP / SLP modes only) NOTE: Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture may revert to Black and White. 3)Press the PLAY button to return to normal speed. NOTES: · Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time. · This function will not operate in recording mode. In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction. 1 2 Insert a tape. Select "TIME SEARCH" mode Press the TIME SEARCH button (with each push it will increase by 10 minute). 3 Enter your desired time ZERO RETURN This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding. Then, press the F. FWD/B button. VERTICAL HOLD CONTROL In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button. NOTE: If there are video noise lines on the screen, reposition or reduce them. Refer to "NOISE CANCEL". 2 Set "RENTAL" to [ON] ­ USER'S SET UP ­ Press the PLAY/K or STOP/L button to point to "RENTAL". Press the F. FWD/B or REW/s button until [ON] appears. B RENTAL REPEAT PLAY AUTO RETURN [ON] [OFF] [OFF] 3 Exit the Rental setting TRACKING ADJUSTMENT · Tracking adjustment will be set automatically · (Digital Tracking function) when you start playback. However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHANNEL K or L button until the streaks disappear. To return to the DTR function, stop the tape once and start playback again. Press the MENU button on the remote control to return to the TV mode. 4 Start playback Press the PLAY button to start playback. · Once you select the Rental mode, it stays in effect even after you turn off the TV/VCR. TO CANCEL THE RENTAL MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. Press the MENU button on the remote control to return to TV mode. If there is a power failure of any kind, the unit will retain its memory for this feature. RECORDING TWO DIFFERENT TAPE SPEEDS Before recording, select the tape speed from : SP mode (Standard Play) or SLP mode (Super Long Play). The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each mode. [. . . ] (Ejemplo: 40) 8) Pulse el botón MENU en el mando a distancia. Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa MENU en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta. EN 9J27 AJUSTE DE CANAL Puede programar el sintonizador para buscar todos los canales que recibe en su localidad. [. . . ]