User manual FUNAI SP120C

[. . . ] OWNER'S MANUAL If you need additional operating assistance after reading this owner's manual or to order replacement accessories, please call TOLL FREE : 1-800-242-7158. VIDEO CASSETTE RECORDER SP120C TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. DISPLAY DESCRIPTION PRECAUTIONS IMPORTANT OF CONTROLS SAFEGUARDS INSTRUCCIONES WARRANTY MAINTENANCE SPECIFICATIONS TROUBLESHOOTING GUIDE EN ESPAÑOL PLAYBACK FUNCTION PREPARATION STATUS FOR USE DISPLAY WARNING: CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. [. . . ] jack of "Remote Control Sensor Wire" box (not supplied) when the VCP locates remote cargo area or behind rear seat. Instead of firing at the VCP, you can control its function by locating "Remote Control Sensor Wire" box where it is accessible to signal from remote control unit. *You can't use the remote sensor on the front panel of the VCP when this jack is occupied. SETTING THE CH3/CH4 SWITCH If your TV does not have A/V terminals: When the VCP is in the Playback mode, your TV will receive signals from the VCP on either channel 3 or 4. To use the VCP with your TV, set the selector switch to CH3 or CH4 (which is located in the back of your VCP), whichever is not used for normal broadcasts in your area. Then set your TV to the same channel. TV REMOTE LINK JACK Connect the VCP to the TV (Funai TV) using the "TV Remote Link cable" (not supplied). Instead of firing at the VCP, you can control its function using remote control sensor on your TV (Funai TV). *You can't use the remote sensor on the front panel of VCP when this jack is occupied. *When you connect both REMOTE CONTROL jack and TV REMOTE LINK jack at the same time, REMOTE CONTROL jack takes precedence over the TV REMOTE LINK jack. CH3 CH4 CH3 CH4 TV LINK REMOTE ANT IN ANT OUT [Back of the VCP] ­4­ EN PLAYBACK FUNCTION NORMAL PLAYBACK 1 Insert the prerecorded tape. If the safety tab has been removed, the VCP will start playback automatically. 2 Turn on the TV and set the TV to channel 3 or 4. Now set the CH3/CH4 switch on the back of the VCP to match the channel selected on the TV. · Tracking adjustment will be set automatically (Digital Tracking function) when you start playback. To adjust the tracking manually, press [TRACKING (o/p)] on the remote control. · When a tape has reached the end, the VCP will rewind the tape to the beginning, eject the tape, and turn off the VCP automatically. 4 To stop playback, press [STOP]. PICTURE SELECT This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes. Turn on the TV and set the TV channel to 3 or 4. Now set the CH3/CH4 switch on the back of the VCP to match the channel selected on the TV. The VCP will automatically turn on and playback will start. If play back does not start, press [PLAY]. Press [PICTURE SELECT] repeatedly to select NORMAL or SOFT or SHARP. You can see the current setting on the display. [NORMAL] [SOFT] STILL You can freeze the picture on TV screen by pressing [STILL] during playback. · Usually there will be video "noise" lines (black and white streaks or dots) on the screen. [. . . ] Botón de reproducción (PLAY) 8. Botón de reposición del contador (COUNTER RESET) 9. Botón de repetición automática (AUTO REPEAT) 10. Botón selector para cintas de alquiler (PICTURE SELECT) 11. [. . . ]