User manual FUNAI SRC413ACV

[. . . ] THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. [. . . ] Press the PAUSE or RECORD button to resume recording. NOTES: · After 5 minutes, the unit will automatically switch to the Recording mode to prevent tape damage. · If "CLOSED CAPTION (ON)" is selected, the OnScreen Display will appear for 5 seconds, then disappear. PAUSE SP 1 Select the channel to be recorded Press the number buttons on the CH 10 remote control or the CHANNEL button K or L. Remember: If the unit is connected to a cable box or satellite box, it must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). SP 3 Begin recording REC Press the RECORD button. SP 4 Stop recording Press the STOP button when recording is completed. - 30 - EN 1C29 OTR (One Touch Recording) TV/VCR This function enables you to set a recording length simply by pressing the REC/OTR button on the unit. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) NOTES: · You cannot start OTR with the remote control. · Recording starts immediately when the REC/OTR button is pressed. · When the REC/OTR button is pressed 18 times, the unit returns to the Normal Recording mode. · To stop the OTR operation, press the STOP button on the unit or on the remote control. · To show the remaining time, press the DISPLAY button on the remote control so that "OTR" appears on the TV screen. (It will show up momentarily then disappear. ) · Recording stops when 0:00 is reached. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) · The channel you want to record is properly set in advance. (Refer to page 18. ) Avoid over lap of programs . . . There is a chance that a program will not be recorded, when programs overlap; · The program with an earlier start has priority. · Once the earliest program finishes, the overlapping programs will begin recording in sequence. · The illustration below demonstrates the sequence of recordings. Program 1 10:00AM - 11:00AM Program 2 9:00AM - 10:00AM Program 3 9:30AM - 12:00PM Recording Sequence Program 1 10:00AM-11:00AM Program 2 9:00AM-10:00AM Program 3 9:30AM-12:00PM 9:00AM 10:00AM 11:00AM 12:00PM 1 Select "TIMER PROGRAMMING" - TV/VCR SETUP B TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH Press the SETUP button on the remote control. Confirm "TIMER PROGRAMMING" is pointed by pressing the Arrow button K, and press the ENTER button. · If you have not yet set the clock, "MANUAL CLOCK SET" appears. If so, follow steps [3] to [8] on pages 15, 16. Then set the timer recording. 2 Select your desired program position (1~8) ­ TIMER PROGRAMMING ­ CH DATE B-/-/-/-/-/-/-/-/BEGIN END -:-:-:-:-:-:-:-:-:- -:- -:- -:- -:- -:- -:- -:- - Press the Arrow button K or L to select the desired program position. Then press the Arrow button B. 3 Set the channel number ­ TIMER PROGRAMMING ­ BEGIN END -:- -:- -:- -:- -:- -:- -:- -:- CH DATE -/-/-/-/-/-/-/-/- Press the Arrow button K or L until the desired channel number appears. [. . . ] (Ejemplo: 5, PM) Luego, pulse el botón B. 7) Pulse el botón K o L hasta que aparezca el minuto deseado. (Ejemplo: 40) 8) Pulse el botón SETUP en el mando a distancia. Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa SETUP en el mando a distancia. [. . . ]