User manual FUNAI SRCD427P

[. . . ] OWNER'S MANUAL COLOR TV/VCR/DVD TRIPLE COMBO SRCD427P (27 inch) SUPPLIED ACCESSORIES ACCESSORIES Batteries PART NO. 2 AA Batteries 1EMN20050 Remote Control Unit NE204UD INSTRUCCIONES EN ESPAÑOL INCLUIDAS. As an ENERGY STAR ® Partner, our company has determined that this product meets the ENERGY STAR ® guidelines for energy efficiency. registered mark. Owner's Manual If you need additional operating assistance after reading this owner's manual, please call TOLL FREE : 1-800-968-3429. Please read before using this equipment WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. [. . . ] WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect your unit and a Source (Playing) VCR or camcorder using the following diagram. [The TV/VCR/DVD] EL REC/OTR REW PLAY F. FWD STOP HEADPHONE VIDEO L AUDIO R [Fig. 8] EJECT [Ex: Source (playing) VCR or camcorder] Audio/Video adapter cable (not supplied) AUDIO L OUT R VIDEO OUT IN IN 1 Select the channel to be recorded Press the number buttons on the remote control or the CHANNEL button K or L. Remember: If the unit is connected to a cable box or satellite box, it must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). 3 1)Insert a pre-recorded video cassette into the Source (Playing) VCR or camcorder. 2)Insert a blank video cassette or one you want to record over, into the unit's cassette compartment. 3)Press the SPEED button on remote control for the unit to select the desired recording speed (SP/SLP). 4)Press the CHANNEL button K or L on the unit until "AUX" appears on the screen. 6)Begin playback of the tape in the source (Playing) VCR or camcorder. NOTE: For best results during copying, use the unit's front panel controls whenever possible. The remote control might affect the source (Playing) VCR's playback operation. 7)To stop copying, press the STOP/EJECT button on the unit, then stop the tape on the source VCR or camcorder. Begin OTR OTR(2 : 30) Press the REC/OTR button on the unit as many times as needed. The recording length will be determined by the number of times you press the REC/OTR button. Each additional push will increase the recording time by 30 minutes. It is set up to a maximum of 8 hours. SP - 31 - EN 1C29 TIMER AUTOMATIC TIMER RECORDING TV/VCR You may set the unit to start and end a recording while you are away. You can set 8 programs to record on specific days, daily or weekly within a 1 year period. In the example below, the timer is being set to record: DATE: July 4th, 2004 SETTING TIME: from 7:30PM to 8:50PM CHANNEL: CH61 TAPE SPEED: SP Make sure . . . · If a cable box or satellite box is connected with the unit you will be limited to record only one channel, and the channel on the unit must be selected to the output channel of the box CH 3 or CH 4 and then the actual channel to be recorded must be selected on the box. · Clock must be set to the correct time and date before setting the timer. · The unit is turned on to program it. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) · The channel you want to record is properly set in advance. (Refer to page 18. ) Avoid over lap of programs . . . There is a chance that a program will not be recorded, when programs overlap; · The program with an earlier start has priority. [. . . ] Utilice esta función para sincronizar el reloj con la hora correcta. 2 Empiece el prefijado automático Pulse el botón K o L para señalar "AUTOPROGRAMACION DE CA". A continuación, pulse el botón ENTER. El sintonizador busca y memoriza todos los canales activos en su localidad. SECCIÓN DE DVD REPRODUCCIÓN BÁSICA DVD-V Para empezar ¡Conecte la alimentación del amplificador y otros CD MP3 3 Después de buscar El sintonizador se detiene en el canal memorizado más bajo. · Cuando se activa AUTOPROGRAMACION DE CA, donde no hay entrada de señal del televisor, aparecerá "NO HAY SEÑAL DE TV" en la pantalla después de terminar la búsqueda de canales. [. . . ]