User manual FUNAI SSD800

[. . . ] OWNER'S MANUAL DVD PLAYER with VIDEO CASSETTE RECORDER SSD800 INSTRUCCIONES EN ESPAÑOL INCLUIDAS. If you need additional assistance for set-up or operating after reading owner's manual, please call TOLL FREE : 1- 800 - 968-3429 Please read before using this equipment. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. [. . . ] the information you entered for the timer recording will not be cleared). TO STOP AN AUTOMATIC TIMER PROGRAM ALREADY STARTED Press the STOP/EJECT or the TIMER SET button on the DVD /VCR. 6 When you finish programming, press the TIMER SET button to activate the timer. ¡As the TIMER SET light comes on the VCR TO CHECK, CORRECT, OR CANCEL AN AUTOMATIC TIMER PROGRAM 1 Turn the power on by pressing the POWER button. (If the VCR is in TIMER STANDBY status, press the TIMER SET button instead of the POWER button. ) becomes STANDBY status, and switches to DVD OUTPUT mode automatically. ¡When DVD sits idle for more than thirty-five minutes, the DVD power will be turned off automatically. If you press the TIMER SET button under such condition, the VCR power will be turned off and become STANDBY status. 2 Select main menu by pressing the MENU button. 3 Select "TIMER PROGRAMMING" by pressing the PLAY or the STOP button. Then, the F. FWD button. TO CLEAR A PROGRAM Follow the steps from 2 to 3. Select the program number you want to clear, and then press the REW button. 4 Select the program number which you want to check by pressing the PLAY or the STOP button. ¡The details of the selected program appears on the HINTS FOR TIMER RECORDING VCR ¡If there is a power failure or the VCR is unplugged TV screen. ¡Go to the digit you want to change by pressing the F. FWD or the REW button. Then, enter correct numbers by pressing the PLAY or the STOP button. for more than 30 seconds, the clock setting and all ¡You may cancel the entire program by pressing the timer settings will be lost. REW button while the program number flashes. ¡If a tape ends during TIMER RECORDING, the VCR will stop, eject the tape, and switch to the DVD 5 Press the CLEAR/C. RESET button to exit. mode automatically as the TIMER SET light blinks. 6 Press the TIMER SET button to return to (If the DVD power is off, the VCR will become timer stand-by mode. EN ­ 21 ­ 1L25 SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the VCR instead of using the jacks on the back. [Recording VCR] (this unit) DVD/VCR OUT IN ANT - IN L AUDO R ANT - OUT 3CH 4CH VIDEO R Cb DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT PCM / BITSTREAM OUT COAXIAL COMPONENT VIDEO OUT RCA-type connectors. Standard audio cables are not recommended. ¡You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR. TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3 or 4. ¡Now set the CH3/CH4 switch on the back of the DVD /VCR to match the channel selected on the TV. 2 Press the VCR/TV button on the recording VCR so that the VCR/TV Light comes on. MTS (Multi-Channel Television Sound) SYSTEM VCR When you play a VHS tape, or receive a broadcast on the VCR tuner channel you are watching, the current status will appear when you press the DISPLAY button on the remote 1)* control. When you record a MTS broadcast signal, you need to set it 2)* to MTS mode. STOP 12:00AM CH 32 STEREO SAP SP 0:00:00 HIFI Cr Coaxial cable (supplied) [TV set] (Use for monitoring) Audio/Video cables (not supplied) LEFT RIGHT OUT IN VIDEO AUDIO ANT in [Playing VCR] (another source) 1)* When a program is broadcast in stereo, STEREO appears. [. . . ] En este caso, siga el paso [3]. 2 Seleccione "CLOCK SET" presionando [PLAY]o [STOP]. Luego, presione [F. FWD] 1 Presione el Botón POWER. ¡La alimentación se conectará. Compruebe que la Luz DVD OUTPUT está encendida. Si no, presione el Botón DVD en el control remote para cambiar el modo DVD. 3 Ajuste el reloj. 1) Ajuste el mes Presione [PLAY] o [STOP] repetidamente Luego, presione [F. FWD]. 2) Ajuste el día 2 Presione el Botón OPEN/CLOSE. ¡La bandeja de carga del disco se abrirá. Presione [PLAY] o [STOP] repetidamente Luego, presione [F. FWD]. 3) Ajuste el año 3 Ponga un disco en la bandeja. ¡Asegúrese de que el disco está asentado correcta- mente, con el lado de la etiqueta arriba. Presione [PLAY] o [STOP] repetidamente Luego, presione [F. FWD]. [. . . ]