User manual FUNAI WF13

[. . . ] THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. [. . . ] (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) NOTES: · This TV/VCR/DVD will ONLY record and view the same channel. · This TV/VCR/DVD cannot record the contents from the built-in DVD. NORMAL RECORDING TV/VCR You can ONLY watch the same TV program that is being recorded. SKIPPING UNWANTED SCENES DURING RECORDING TV/VCR Press the PAUSE button to temporarily stop recording. Press the PAUSE or RECORD button to resume recording. NOTES: · After 5 minutes, the TV/VCR/DVD will automatically switch to the Recording mode to prevent tape damage. · If "CLOSED CAPTION (ON)" is selected, the OnScreen Display will appear for 5 seconds, then disappear. PAUSE SP 1 Select the channel to be recorded Press the number buttons on the CH 10 remote control or the CHANNEL button K or L. Remember: If the TV/VCR/DVD is connected to a cable box or satellite box, the TV/VCR/DVD must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box. 2 Select the tape speed Press the SPEED button to select the desired tape speed (SP/ SLP). SP 3 Begin recording REC Press the RECORD button. SP 4 Stop recording Press the STOP button when recording is completed. - 30 - EN 1C29 OTR (One Touch Recording) TV/VCR This function enables you to set a recording length simply by pressing the REC/OTR button on the TV/VCR/DVD. · TV/VCR/DVD power must be turned on. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) NOTES: · You cannot start OTR with the remote control. · Recording starts immediately when the REC/OTR button is pressed. · When the REC/OTR button is pressed 18 times, the TV/VCR/DVD returns to the Normal Recording mode. In the example below, the timer is being set to record: DATE: July 4th, 2004 SETTING TIME: from 7:30PM to 8:50PM CHANNEL: CH61 TAPE SPEED: SP Make sure . . . · If a cable box or satellite box is connected with the TV/VCR/DVD you will be limited to record only one channel, and the channel on the TV/VCR/DVD must be selected to the output channel of the box CH 3 or CH 4 and then the actual channel to be recorded must be selected on the box. · Clock must be set to the correct time and date before setting the timer. · TV/VCR/DVD power must be turn on to program it. · Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording. ) · The channel you want to record is properly set in advance. (See page 18. ) Avoid over lap of programs . . . There is a chance that a program will not be recorded, when programs overlap; · The program with an earlier start has priority. · Once the earliest program finishes, the overlapping programs will begin recording in sequence. · The illustration below demonstrates the sequence of recordings. Program 1 10:00AM - 11:00AM Program 2 9:00AM - 10:00AM Program 3 9:30AM - 12:00PM Recording Sequence Program 1 10:00AM-11:00AM Program 2 9:00AM-10:00AM Program 3 9:30AM-12:00PM 9:00AM 10:00AM 11:00AM 12:00PM 1 Select "TIMER PROGRAMMING" - TV/VCR SETUP B TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN TIME SEARCH INDEX SEARCH Press the SETUP button on the remote control. [. . . ] (Ejemplo: 5, PM) Luego, pulse el botón B. 7) Pulse el botón K o L hasta que aparezca el minuto deseado. (Ejemplo: 40) 8) Pulse el botón SETUP en el mando a distancia. Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa SETUP en el mando a distancia. [. . . ]