User manual FUNAI WF802

[. . . ] OWNER'S MANUAL DVD PLAYER with VIDEO CASSETTE RECORDER WF802 INSTRUCCIONES EN ESPAÑOL INCLUIDAS. If you need additional assistance for set-up or operating after reading owner's manual, please call TOLL FREE : 1- 800 - 242-7158 Please read before using this equipment. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. [. . . ] Press the VCR/TV button to choose VCR position. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don't have to set the TIMER off to use the DVD. 5 To set another program, repeat step [4]. To exit from the set up screen, press the CLEAR/C. RESET button (You only exit from the set up screen. the information you entered for the timer recording will not be cleared). TO STOP AN AUTOMATIC TIMER PROGRAM ALREADY STARTED Press the STOP/EJECT or the TIMER SET button on the DVD /VCR. 6 When you finish programming, press the TIMER SET button to activate the timer. ¡As the TIMER SET light comes on the VCR TO CHECK, CORRECT, OR CANCEL AN AUTOMATIC TIMER PROGRAM 1 Turn the power on by pressing the POWER button. (If the DVD/VCR is in TIMER STANDBY status, press the TIMER SET button instead of the POWER button. ) becomes STANDBY status, and switches to DVD OUTPUT mode automatically. ¡When DVD sits idle for more than thirty-five minutes, the DVD power will be turned off automatically. If you press the TIMER SET button under such condition, the DVD/VCR power will be turned off and become STANDBY status. 2 Select main menu by pressing the MENU button. 3 Select "TIMER PROGRAMMING" by pressing the PLAY or the STOP button. Then, press the F. FWD button. TO CLEAR A PROGRAM Follow the steps from 2 to 3. Select the program number you want to clear, and then press the REW button. 4 Select the program number which you want to check by pressing the PLAY or the STOP button. ¡The details of the selected program appears on the HINTS FOR TIMER RECORDING VCR ¡If there is a power failure or the DVD/VCR is TV screen. ¡Go to the digit you want to change by pressing the unplugged for more than 30 seconds, the clock setting and all timer settings will be lost. ¡If a tape ends during TIMER RECORDING, the VCR will stop, eject the tape, and switch to the DVD 5 mode automatically as the TIMER SET light blinks. 6 (If the DVD power is off, the DVD/VCR will become STANDBY status). ­ 21 ­ F. FWD or the REW button. Then, enter correct numbers by pressing the PLAY or the STOP button. ¡You may cancel the entire program by pressing the REW button while the program number flashes. Press the CLEAR/C. RESET button to exit. Press the TIMER SET button to return to timer stand-by mode. EN 1L25 SPECIAL FEATURES COPYING A VIDEO TAPE VCR You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording DVD/VCR (this unit), the playing VCR (another source) and your TV using the following diagram. ¡You can use the AUDIO/VIDEO input jacks on the front panel of the DVD/VCR instead of using the jacks on the back. [Recording VCR] (this unit) DVD/VCR OUT IN ANT - IN L AUDO R ANT - OUT 3CH 4CH VIDEO R DVD/VCR AUDIO OUT L S-VIDEO DIGITAL AUDIO OUT PCM / BITSTREAM OUT COAXIAL ¡Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended. [. . . ] ¡Si el reloj no está ajustado, aparece primero el menú CLOCK SET. En este caso, siga el paso [3]. 2 Seleccione "CLOCK SET" presionando [PLAY]o [STOP]. Luego, presione [F. FWD] 1 Presione el Botón POWER. ¡La alimentación se conectará. Compruebe que la Luz DVD OUTPUT está encendida. [. . . ]