User manual FURMAN MP20Q

[. . . ] Maintained switches, such as most toggle switches, push-on/push-off button switches, and the Furman RS-1 locking key switch, stay open until thrown, then stay closed until thrown again. Momentary switches, usually pushbutton types, are normally open and stay closed only as long as the button is pressed. Maintained switches are most convenient when there is only one remote switch location; momentary switches allow turn-on or turn-off from multiple locations. MiniPorts come factory-configured for maintained operation. [. . . ] The ON or OFF state begins on the rising edge of the signal. The Furman RS-1 Remote System Control Panel is an attractively finished key switch designed for use in single-gang wall mount boxes. It can control, from one location, most Furman power products that have remote capability. The RS-2 Remote System Control Panel is identical to the RS-1 in most respects, but with a momentary function rather than maintained. The RS-2 is ideal for installations requiring multiple remote switches. IMPORTANT NOTE REGARDING MOMENTARY MODE: If multiple MiniPorts are being controlled in Momentary Mode, power loss to any one of the units will likely cause its memory to be different than that of the other units. Not only will this be irritating, it can also be dangerous, as it may be ON when the others are OFF. To correct this potential problem (as exists in any simple momentary switch product), our thoughtful engineers devised a simple method of holding the switch down (REM to +12) for at least four seconds. This resets all units to the OFF condition, and avoids having to disconnect AC power from all units. MiniPort 20-Q/15Q Quad Box Power Relays The new 20-amp MiniPort-20Q and the MiniPort-15Q (15 amps) provide a pair of remotely-activated, relaycontrolled outlets, set up for mounting in any standard electrical quad box, either directly or with a "mud ring" attached. Due to the space limitations of a quad box, the MiniPort "Q" models MINIPORT-15Q MINIPORT-20Q POWER RELAY POWER RELAY have a smaller feature set POWER thanPOWER MiniPort-15 and the MiniPort-20. MiniPor t-Q's have no internal power supply; + + a maintained 8-15 VDC supply capable of supplying 10 mA is required to turn on the outlets. This can be supplied by a Furman PowerLink, ASD-120, or a PS-8R (with a simple internal modification to the PS-8R. ) Solder pads are available on the circuit board to allow control wiring from inside the quad box. 120 VAC 60 Hz MAX LOAD 20 A 120 VAC 60 Hz MAX LOAD 15 A CLASS 2 WIRING CLASS 2 WIRING NC NC 8-15VDC TO TURN ON 8-15VDC TO TURN ON Linking Multiple Units Multiple MiniPorts may be connected together so that all are controlled by a single switch closure. All the units must be set to the same mode depending on the type of switch or switches to be used (use momentary mode and momentary switches if more than one switch is required. ) All the units must be paralleled by tying together all the +12V terminals, all the REM terminals, and all the GND terminals (see Figure 1). Multiple MiniPorts may be linked so that they all turn on simultaneously, as discussed above, or in a delayed sequence. In a delayed sequence, only the turn-ons are delayed (all turn-offs occur simultaneously. ) This feature is particularly useful in staggering the turn-on of large power amps to avoid large inrush currents that might trip the house circuit breakers. The delay interval is approximately two to three seconds (the first unit turns on with the switch closure, the second in the chain about 3 seconds later, the third unit 3 seconds after the second, etc. ) The choice of delayed or simultaneous linking is available regardless of whether maintained or momentary switching is used. However, if delayed linking is used with momentary switching, only the first MiniPort should be set to momentary mode, and all momentary switches should be connected in parallel between the first unit's +12V and REM terminals. The second and subsequent MiniPorts must be left in maintained mode. See Figure 2. Dimensions The MiniPorts' body dimensions are: 5. 5" (H) x 3. 75" (W) x 2" (D). The baseplate is 5. 25" square. Differences From the Earlier MiniPort The MiniPort-20 and MiniPort-15 are upgraded versions of an earlier product designated simply "MiniPort". These new MiniPorts are equipped for remote operation using either maintained or momentary contact switches to initiate the turn-on or turn-off. (The original MiniPort required maintained contact switches. ) Also, a Delay Out terminal has been added to permit sequenced turn-on when multiple MiniPorts are linked. Finally, the new MiniPorts have the previously described knockout holes at top and bottom for permanent installation with 1/2" metal conduit. Three Year Limited Warranty All Furman MiniPort models are protected by a limited three year warranty, covering defects in materials and workmanship, provided that the registration card is filled out and returned by the customer. [. . . ] Do not connect the STATUS terminals of multiple units together. Knockout Holes Both the MiniPort-15 and the MiniPort-20 come equipped with two knockout holes for permanent installation with 1/2" conduit -- one on the top surface, the other on the bottom. Use of the bottom knockout hole requires removing the AC cord. The National Electrical Code allows for up to eleven 14awg conductors of THHN/THWN/THWN-2 type in 1/2" conduit (MiniPort-15) or up to eight 12awg conductors (MiniPort-20). For grounding and other details, please consult a licensed electrician. Service Before returning any equipment for repair, please be sure that it is adequately packed and cushioned against damage in shipment, and that it is insured. [. . . ]