User manual FURMAN PSPRO

[. . . ] PS-PRO - POWER CONDITIONER/SEQUENCER PS-PRO - POWER CONDITIONER/SEQUENCER Congratulations on your purchase of a Furman PS-PRO Power Conditioner/Sequencer. The PS-PRO is one of Furman's top-of-the-line PRO Series, offering maximum protection from the AC line hazards faced by delicate analog and digital pro audio and video F E AT U R E S l 20 amp (2400 watt) rating handles even the largest amps Multiple levels of protection components can safely absorb large voltage spikes and provide highly effective RF filtering -- the most comprehensive protection available anywhere!Extreme Voltage Shutdown guards against catastrophically wrong voltages Power Status LED's indicate which outlet groups have power Mains Wiring indicators monitor wiring integrity, show Normal and five kinds of faults Remote operation allows turn-on and turn-off at a distance simply by connecting a momentary or maintained-contact switch (and LED if desired) Multiple units may be linked to handle higher currents and/or more than three delay groups Six switched outlets (on rear panel), and three unswitched outlets (one front, two rear) Ten foot 12 AWG heavy duty power cord l l l l The PS-PRO is a power sequencer, meaning it is capable of powering a rack full of equipment in three steps separated by timed delays. It is useful whenever various kinds of equipment must be powered up or down in groups, rather than all simultaneously. [. . . ] During the power-down delay cycle, each LED goes off as power to its corresponding outlet is removed. In addition, the Delay 1 LED flashes if a remote switch (or the stored state) is OFF. MAINS WIRING INDICATORS: The PS-PRO assists in analyzing any faults that may occur in the AC mains wiring. Three neon indicators (two green and one red) light in a specific pattern for normal wiring and in different patterns for various faults. When the AC wiring is correct, both green indicators will be lit. If a fault is present, the chart immediately above the neon indicator will identify the exact nature of the 5 PS-PRO - POWER CONDITIONER/SEQUENCER fault. Since any wiring fault presents a potentially serious safety hazard, the assistance of a qualified electrician should be obtained in correcting the problem. NOTE: The Mains Wiring indicators and status LEDs stay on even when the power switch is off. This feature allows you to check the mains wiring before powering up your equipment. These indicators are designed for continuous, ongoing use. Like a clock, they consume very little power. UNSWITCHED OUTLET: This convenient outlet provides power at all times when the PS-PRO is plugged in and operating under normal power conditions. ON/REM/OFF SWITCH: When turned to the ON position, this key lock switch initiates an ON sequence, applying power to the PS-PRO's switched outlets. When turned to the OFF position, it begins an OFF sequence. In the REM position, the PS-PRO will accept on/off commands from a remote switch or switches that may be connected to the rear panel terminals. CIRCUIT BREAKER: The overall capacity of the PS-PRO is 20 amps. If the combined steady-state current drawn by all devices plugged into all of its nine outlets level exceeds 20 amps at any time, the circuit breaker will trip, cutting off power to your rack. If this occurs, you must reduce the load by unplugging one or more units from the PS-PRO, and reset it. You can reset the circuit breaker by simply pressing in the button, which pops out when tripped. However, because it is a thermal type, you may have to wait a few moments after it trips for it to cool down before it will allow you to reset it. UNSWITCHED OUTLETS: The PS-PRO rear panel provides clean, filtered power to this pair of unswitched outlets, adjacent to the power cord. SWITCHED (DELAYED) OUTLETS: The PS-PRO rear panel provides three pairs of switched outlets, widely spaced to allow use of equipment with plug- in (wall wart) transformers. [. . . ] Products must have a proof of purchase from a Furman authorized dealer. During this period, Furman will make any necessary repairs without charge for parts or labor. Shipping charges to the factory or repair station must be prepaid by the owner; return shipping charges (via UPS Ground) will be paid by Furman. This warranty applies only to the original owner and is not transferable. [. . . ]