User manual FURMAN PSPRO II

[. . . ] PS-PRO II - POWER CONDITIONER / SEquENCER PS-PRO II - POWER CONDITIONER / SEquENCER F E aT u R E S n INTRODuCTION Thank you for purchasing the PS-PRO II, and congratulations on your choice. The Series II power conditioners feature Furman's revolutionary Series Multi-Stage Protection Plus (SMP+) circuit, as well as our exclusive Linear Filtering Technology (LiFT). Together, these technologies comprise, without question, the world's most advanced and comprehensive transient voltage surge suppressor / conditioner. SMP+ (Series Multi-Stage Protection Plus) non-sacrificial surge suppression -- the most comprehensive protection available anywhere!LiFT (Linear Filtering Technology) with zero ground contamination Extreme voltage shutdown BNC connector on the rear panel allows for attachment of a gooseneck lamp to illuminate the rear of your rack Power Status LED's indicate which outlet groups have power Remote operation allows turn-on and turn-off at a distance simply by connecting a momentary or maintainedcontact switch (and LED if desired) Multiple units may be linked to handle higher currents and/or more than three delay groups Six switched outlets (on rear panel), and three unswitched outlets (one front, two rear) Ten foot 12 AWG heavy duty power cord n n n SMP+ (Series Multi-Stage Protection Plus) n n Furman's SMP+ surge suppression virtually eliminates service calls. [. . . ] It then acts the same as any other remote momentary switch that may be connected to the rear panel terminal strip. If the switched outlets are on, pushing it begins an OFF sequence. If they are off, pushing it begins an ON sequence. Do not use this switch when in Maintained Mode. PROTECTION OK: This LED is normally on when the power to the PS-PRO II's outlets is switched on. It monitors the integrity of the protection devices and reports if the protection is compromised. If an extremely large spike is encountered that exceeds the PS-PRO II's capacity, the main group of input protectors will blow an internal fuse, causing the indicator to go out. If this occurs, reduce the load by unplugging one or more units from the PS-PRO II, and reset it. you can reset the circuit breaker by simply pressing the button, which pops out when tripped. However, because it is a thermal type, you may have to wait a few moments after it trips for it to cool down before it will allow you to reset it. ON/REm/OFF SWITCH: When turned to the ON position, this key lock switch initiates an ON sequence, applying power to the PS-PRO II's switched outlets. When turned to the OFF position, it begins an OFF sequence. In the REM position, the PS-PRO II will accept on/off commands from a remote switch or switches that POWER STaTuS (DElaY) lEDs: One green LED is provided for each of the three delay stages. Each LED lights when power is applied to its corresponding duplex outlet on the rear panel. All three LEDs then remain lit until power is removed. During the power-down delay cycle, each LED goes off as power to its corresponding outlet is removed. In addition, the Delay 1 LED flashes if a remote switch (or the stored state) is OFF. uNSWITCHED OuTlET: This convenient outlet provides power at all times when the PS-PRO II is plugged in and operating under normal power conditions. CIRCuIT BREaKER: The overall capacity of the PS-PRO II is 20 amps. Should the com- REaR PaNEl BNC Connector for rear light (models GN-I or GN-LED) may be connected to the rear panel terminals. UNSWITCHED OUTLETS: The PS-PRO II rear panel provides clean, filtered power to this pair of unswitched outlets, adjacent to the power cord. SWITCHED (DELAyED) OUTLETS: The PS-PRO II rear panel provides three pairs of switched outlets, widely spaced to allow use of equipment with plug- in (wall wart) transformers. [. . . ] Return shipping charges back to Purchaser will be paid by Manufacturer. THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITy AND FITNESS FOR A PARTICULAR PURPOSE. Manufacturer does not warrant against damages or defects arising out of improper or abnormal use of handling of the Product; against defects or damages arising from improper installation, against defects in products or components not manufactured by Manufacturer, or against damages resulting from such non-Manufacturer made products or components. This warranty shall be cancelable by Manufacturer at its sole discretion if the product is modified in any way without written authorization from Furman Sound. [. . . ]