User manual FURMAN PWRKITTL INSTALLATION INSTRUCTION

[. . . ] The modular signal connection allows for a variety of installation options. POWER OUTLET FACEPLATE: This modular interface has added noise filtration to eliminate any unwanted radiated interference. POWER CORD (MPC-IEC): 24 inch IEC power cord. 1690 Corporate Circle, Petaluma, CA 94954 · Fax 707-763-1310 · www. FurmanSound. com 080206 Power Inlet Faceplate Installation Instructions CAUTION: Not for use in "Fire-Break" walls unless used in conjunction with signal-line modules! 4 in. STEP 1: 3 3/4 in. 1 Select a location close to the head-end source equipment. Cut a 4-inch wide by 3 3/4-inch high hole in the wall. [. . . ] NOTE: Wire nuts are not recommended for high-current applications such as powered subwoofers. NOTE: 4 STEP 4: Neatly fold the AC wires as you install the inlet faceplate into the wall with the AC side fitting into the outlet box. Secure the unit to the outlet box with the included screws. NOTE: Only the right side screws are used to mount the inlet faceplate into the included outlet box. The left side screws are for appearance only and are held on with the included plastic washers. All four screws are used when mounting the protector to a new-work electrical box and low voltage add-on bracket. PAGE 2 Power Outlet Faceplate Installation Instructions CAUTION: Not for use in "Fire-Break" walls! 4 in. STEP 1: 3 3/4 in. 1 Select a location close to the display device (Plasma TV, DLP, etc. ). In the case of a wall-mounted Plasma TV, this may be behind the display device and totally hidden from view once the Plasma TV is mounted. Cut a 4-inch wide by 3 3/4-inch high hole in the wall for the in wall power cable (not included) and signal wires (not included). NOTE: For new construction (pre-wire): Use a Carlon new-work electrical box (Model B122A). A Carlon low voltage add-on bracket (Model SCIOOSC) may be used to indicate the size and location of the opening needed in the drywall. The low-voltage bracket may be left in place when installing the outlet faceplate. STEP 2: 2 Run the AC wires through the lower-left entry of the included outlet box. No more than 1 inch of wire sheath should extend into the outlet box. 3 inches of wire should be able to extend beyond the opening of the outlet box. Install the outlet box into the right side of the hole. 3 STEP 3: Slide the included shrink-wrap tubing over the ground wire to prevent contact with the circuit board. Use the included wire nuts to connect the wires. Note: Wire nuts not recommended for high current applications such as powered subwoofers. STEP 4: 4 Neatly fold the AC wires as you install the outlet faceplate into the wall with the AC side fitting into the outlet box. Secure the unit to the outlet box with the included screws. NOTE: Only the right side screws are used to mount the inlet faceplate into the included outlet box. The left side screws are for appearance only and are held on with the included plastic washers. All four screws are used when mounting the protector to a new-work electrical box and low voltage add-on bracket. PAGE 3 Furman PowerKit-TL Product Warranty LIMITED THREE YEAR WARRANTY Furman Sound, Inc. , having its principal place of business at 1690 Corporate Circle. , Petaluma, CA 94954 ("Manufacturer") warrants its PowerKit-TL (the "Product") as follows: Manufacturer warrants to the original Purchaser of the Product that the Product sold hereunder will be free from defects in material and workmanship for a period of three years from the date of purchase. The Purchaser of the product is allowed fifteen days from the date of purchase to complete warranty registration by mail or on-line at the Furman website. [. . . ] The sole and exclusive obligation of Manufacturer shall be to repair or replace the defective Product in the manner and for the period provided above. Manufacturer shall not have any other obligation with respect to the Products or any part thereof, whether based on contract, tort, strict liability or otherwise. Under no circumstances, whether based on this Limited Warranty or otherwise, shall Manufacturer be liable for incidental, special, or consequential damages. Manufacturer's employees or representatives' ORAL OR OTHER WRITTEN STATEMENTS DO NOT CONSTITUTE WARRANTIES, shall not be relied upon by Purchaser, and are not a part of the contract for sale or this limited warranty. [. . . ]