User manual FURUNO CU-300 REFERENCE GUIDE

[. . . ] Turn off the power at the switchboard if the equipment becomes abnormally warm or is emitting odd noises. Contact a FURUNO dealer or agent for advice. Make sure no rain or water splash leaks into the equipment. Fire or electrical shock can result if water leaks in the equipment. i WARNING Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. CU-300 CAUTION Observe the following compass safe distances to prevent interference to a magnetic compass: Standard compass Steering compass 0. 70 m 0. 45 m Attach grounding securely to ship's body. [. . . ] D-1 iii SYSTEM CONFIGURATIONS The Memory Card Interface Unit CU-300 connects to a processor unit of MODEL18x4C-BB/ 19x4C-BB or GD-1920C-BB (NavNet VX2-BB) to provide a card drive(s) in a remote location(s). Power to the CU-300 is supplied from the processor unit. Maximum four units can be connected via a HUB. Note that the CU-300 can be connected only to the NavNet VX2 units which have the following software version No. C-MAP specification Type MODEL 18x4C-BB/19x4C-BB, GD-1920C-BB MODEL 18x4C/19x4C, GD-1920C MODEL 17x4C, GD-1720C Version No. 1950026-02. 01 and after 1950024-02. 01 and after 1950028-02. 01 and after NAVIONICS specification Type MODEL 18x4C-BB/19x4C-BB, GD-1920C-BB MODEL 18x4C/19x4C, GD-1920C MODEL 17x4C, GD-1720C Version No. 1950025-01. 09 and after 1950023-01. 09 and after 1950027-01. 09 and after iv Connection to single NavNet VX2-BB unit CU-300 Power cable MJ-A3SPF0026-050C or 100C Model 18x4C-BB/19x4C-BB GD-1920C-BB Ethernet cable MJ-A6SPF0017-050C or 100C Connection to multiple NavNet VX2-BB units CU-300 Power cable MJ-A3SPF0026-050C or 100C Model 18x4C-BB/19x4C-BB GD-1920C-BB LAN cable (CAT5, STP, straight) Model 18x4C-BB/19x4C-BB, GD-1920C-BB, Model 18x4C/19x4C, GD-1920C Model 17x4C or GD-1720C Model 18x4C-BB/19x4C-BB, GD-1920C-BB, Model 18x4C/19x4C, GD-1920C Model 17x4C or GD-1720C : Standard supply : Local supply : NavNet VX2 : Option for NavNet VX2 HUB v Connection for two CU-300 Model 18x4C-BB/19x4C-BB GD-1920C-BB Model 18x4C-BB/19x4C-BB GD-1920C-BB CU-300 Power cable MJ-A3SPF0026-050C or 100C CU-300 LAN cable (CAT5, STP, straight) HUB : Standard supply : Local supply : NavNet VX2 : Option for NavNet VX2 vi EQUIPMENT LISTS Standard supply Name Memory Card Interface Unit Installation Materials (Select one. ) Type CU-300 CP03-27400 Code No. 000-081-570 Qty 1 1 set For 5 m, MJ-A6SPF0017-050C, MJ-A3SPF0026-050C, and CP03-27401 For 10 m, MJ-A6SPF0017100C, MJ-A3SPF0026-100C, and CP03-27401 For 5 m, MJ-A3SPF0026-050C and CP03-27401 For 10 m, MJ-A3SPF0026-100C and CP03-27401 Remarks CP03-27410 000-081-571 1 set CP03-27440 CP03-27450 000-083-403 000-010-245 1 set 1 set Optional supply Name Hanger Console Mounting Kit Cable Assy Type FP03-10201 FP03-10203 MJ-A3SPF0026-050C MJ-A3SPF0026-100C MJ-A6SPF0017-050C MJ-A6SPF0017-100C Code No. 008-539-530 001-011-710 000-157-944-10 000-157-945-10 000-159-705-11 000-159-706-11 Qty 1 set 1 set 1 1 1 1 Remarks For desktop mounting For bulkhead mounitng 5 m, power cable 10 m, power cable 5 m, Ethernet cable 10 m, Ethernet cable vii 1. MOUNTING The memory card interface unit can be flush mounted in a console, or mountd on a desktop or the overhead. Choose a mounting location for the unit considering the following points: · Leave sufficient space around the unit to facilitate checking and maintenance. See outline drawing at the back of this manual for recommended maintenance space. · Locate the unit well away from exhaust gases and other active gases. · The location should be well ventilated. · Choose a location where shock and vibration are minimal. · Only the front panel is waterproofed. Note: For flush mount or bulkhead mount, the DIP switch setting should be completed before mounting. See page 8. 1. 1 Flush Mounting 1. Prepare a cutout in the mounting location as below. 150. 5+0. 5 54+1 . 2 5 24+0. 5 143+1 2. Screw four threaded rod (M4×50, supplied) into holes on the front panel (reverse side). Screw threaded rods into these holes. R2 4. 5 Rear view Threaded rod 3. Insert the unit into the cutout made at step 1. Fix the unit with four spring, flat washers, and hex. nuts. 1 Spring washer, flat washer and hex. [. . . ] Note that the total number of card slots is maximum four in a series. 2. 1 Connection between One Processor Unit and One Memory Card Interface Unit Ethernet cable MJ-A6SPF0017-050C or 100C POWER 1 F. G. 3 REMOTE FMD DISPLAY 0. 3 A MAX 2 GND OUTPUT 12 VDC NTSC/PAL RGB OUT DJ-1 OPTION 1 2 CARD SLOT 3 GND INPUT 12-24 VDC NETWORK CONT DATA 3 DATA 2 DATA 1 Power cable MJ-A3SPF0026-050C or 100C Ground wire IV-1. 25sq (Local supply) Ground 5 2. 2 Connection between One Memory Card Interface Unit and Multiple Processor Units (Max. Three Units) Prepare the following cables and connectors: · Commercial LAN cable (CAT5, STC, straight) · Cable assy, MJ-A6SPF0014-010C/050C/100C/200C/300C (option for NavNet VX2) · Converter connector, MJA6SERMD/TM11AP8-005 (option for NavNet VX2) Power cable MJ-A3SPF0026-050C or 100C Ground Ground wire IV-1. 25sq (Local supply) POWER 1 F. G. 3 REMOTE FMD DISPLAY 0. 3 A MAX 2 GND OUTPUT 12 VDC NTSC/PAL RGB OUT DJ-1 OPTION 1 2 CARD SLOT 3 GND INPUT 12-24 VDC NETWORK CONT DATA 3 DATA 2 DATA 1 NavNet VX2-BB Processor unit LAN cable (CAT5, STP, straight, local supply) Cable assy MJ-A6SPF0014-010C/ 050C/100C/200C/300C (Option for NavNet VX2) HUB NavNet VX2 or NavNet VX2-BB Processor unit Converter connector MJA6SRMD/TM11AP8-005 (Option for NavNet VX2) NavNet VX2 or NavNet VX2-BB Processor unit 6 2. 3 Connection between Two Memory Card Interface Units and Two Processor Units Prepare the following cables and connectors: · Commercial LAN cable (CAT5, STP, straight) · Cable assy, MJ-A6SPF0014-010C/050C/100C/200C/300C (option for NavNet VX2) · Converter connector, MJA6SERMD/TM11AP8-005 (option for NavNet VX2) Power cable MJ-A3SPF0026-050C or 100C Ground wire IV-1. 25sq (Local supply) Ground POWER 1 F. G. [. . . ]