User manual FURUNO FS-1503

[. . . ] SAFETY INSTRUCTIONS DANGER Never touch the SSB antenna, antenna coupler or lead-in insulator when the SSB radiotelephone is transmitting. High voltage which will cause death or serious injury is present at the locations mentioned above when the SSB radiotelephone is transmitting. Indoor Antenna Wire (High Voltage) Antenna Coupler Antenna Wire WARNING Do not place liquid-filled containers on the top of the equipment. Fire or electrical shock can result if a liquid spills into the equipment. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. [. . . ] Telex operation requires the REMOTE-A Board (option). Note that an Rx narrow filter (option) is also available. FURUNO NBDP Terminal DP-5/DP-6 No special operation is required; class of emission and frequencies are automatically set on the DP-5/DP-6. Select "TLX" with the [MODE/1] key. Tune the antenna coupler by pressing the [TUNE/7] key. Distress frequencies for telephony and telegraphy are as below. For other traffic frequencies, refer to APPENDIX. Telephony SSB (kHz, Carrier) 2182 4125 6215 8291 12290 16420 DSC (kHz, Center) 2187. 5 4207. 5 6312. 0 8414. 5 12577. 0 16804. 5 Telex (kHz, Center) 2174. 5 4177. 5 6268. 0 8376. 5 12520. 0 16695. 0 2-1 2. 2 Remote Station RB-500 (requires optional Remote-B Board) Priority The Remote Station RB-500 usually has higher priority than the FS-1503. This means that operation of the FS-1503 is disabled when the handset of the RB-500 is picked up. The indication "REM" appears on the FS-1503 display when the remote station is in operation and the PTT switch on the microphone of the FS-1503 is inoperative. Communication on 2182 kHz When 2182 kHz is selected on the FS-1503, the FS-1503 takes priority. 2. 3 Intercom The intercom provides communications between the FS-1503 and the RB-500 Remote Station (option). When intercom mode is in use, there is no radio transmission. Calling RB-500 1. "COM" appears on the FS-1503 display panel. The buzzer stops when the handset of the RB-500 is picked up. * Designated number of the RB-500 if more than one is installed. Release the switch to listen. Call from RB-500 When the FS-1503 is called from the RB-500, the FS-1503 releases a buzzer. Press the [INT/0] key to silence the buzzer. Note that the loudspeaker on the FS-1503 is automatically turned on when a call from the RB-500 is received, regardless of setting. Terminating the intercom Press the [INT/0] key to terminate the intercom function. "COM" disappears. 2-2 3. CHANGING SYSTEM SETTINGS 3. 1 System Setup 1. While pressing and holding down the [CH] key, turn on the power. Release the [CH] key when "MEMO" appears on the display. System code Setting value MEMO Figure 3-1 System setting selection screen 2. Turn the [FREQ/CH] control to select a desired code number. Press the [CH] key, enter desired setting by a numeric key, then press the [ENT] key. To change setting for another code, repeat steps 2 and 3. [. . . ] 4001 4002 4003 4004 4005 4006 4007 4008 4009 4010 4011 4012 4013 4014 4015 4016 4017 4018 4019 4020 4021 4022 4023 4024 4025 4026 4027 4028 4029 4030 4031 4032 4033 CH NO. 6001 6002 6003 6004 6005 6006 6007 6008 6009 6010 6011 6012 6013 6014 6015 6016 6017 6018 6019 6020 6021 6022 6023 6024 6025 6026 6027 6028 6029 6030 6031 6032 6033 6034 6035 6036 6037 6038 6039 6040 CH NO. 6041 6042 6043 6044 6045 6046 6047 6048 6049 6050 6051 6052 6053 6054 6055 6056 6057 6058 6059 6060 6061 Above is factory programmed. A-9 8 MHz BAND ITU NBDP (Telex) FREQUENCY TABLE (ITU RR APPENDIX 32) 8 MHz TELEX CH NO. SHIP RX SHIP TX 8001 8376. 5 8376. 5 8002 8417. 0 8377. 0 8003 8417. 5 8377. 5 8004 8418. 0 8378. 0 8005 8418. 5 8378. 5 8006 8419. 0 8379. 0 8007 8419. 5 8379. 5 8008 8420. 0 8380. 0 8009 8420. 5 8380. 5 8010 8421. 0 8381. 0 8011 8421. 5 8381. 5 8012 8422. 0 8382. 0 8013 8422. 5 8382. 5 8014 8423. 0 8383. 0 8015 8423. 5 8383. 5 8016 8424. 0 8384. 0 8017 8424. 5 8384. 5 8018 8425. 0 8385. 0 8019 8425. 5 8385. 5 8020 8426. 0 8386. 0 8021 8426. 5 8386. 5 8022 8427. 0 8387. 0 8023 8427. 5 8387. 5 8024 8428. 0 8388. 0 8025 8428. 5 8388. 5 8026 8429. 0 8389. 0 8027 8429. 5 8389. 5 8028 8430. 0 8390. 0 8029 8430. 5 8390. 5 8030 8431. 0 8391. 0 8031 8431. 5 8391. 5 8032 8432. 0 8392. 0 8033 8432. 5 8392. 5 8034 8433. 0 8393. 0 8035 8433. 5 8393. 5 8036 8434. 0 8394. 0 8037 8434. 5 8394. 5 8038 8435. 0 8395. 0 8039 8435. 5 8395. 5 8040 8436. 0 8396. 0 8041 8396. 5 8396. 5 8042 8397. 0 8397. 0 8043 8397. 5 8397. 5 8044 8398. 0 8398. 0 8045 8398. 5 8398. 5 Above is factory programmed. [. . . ]