User manual FURUNO GP-150

[. . . ] GPS NAVIGATOR GP-150 The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya 662-8580, JAPAN Telephone : Fax : 0798-65-2111 0798-65-4200 All rights reserved. Printed in Japan FIRST EDITION : FEB. OME-44400 ( HIMA ) GP-150 *00015801400* *00015801400* *00015801400* *OME44400A00* *OME44400A00* *OME44400A00* IMPORTANT NOTICE · This manual is intended for use by native speakers of English. · No part of this manual may be copied or reproduced without written permission. · If this manual is lost or worn, contact your dealer about replacement. [. . . ] 4) Press the NU/CU ENT key. Displaying LOPs 1) 2) 3) 4) 5) Press MENU ESC, 9 and 8. Press or to select LC (Loran C) or DE (Decca). 6) Press to select DE Chain. 7) Key in Decca chain number referring to the Decca chain list in the Appendix. For the Europe chain, for example, press 0, 1. to switch from 11) If necessary, press plus to minus or vice versa. 13) Press the MENU ESC key. Follow 1 or 2 in the adjacent column according to selection in step 5. 6-2 6. SETTING UP VARIOUS DISPLAYS Registering waypoints using LOPs 1) Press WPT RTE and 5. 2) Press WAYPOINT LIST (LOP, LC) 001 36365. 2 59102. 3 MARINE POINT AUG12' 95 12 : 35U 002 36512. 3 ___ A POINT 59134. 5 AUG13' 95 13 : 45U 003 _ _ _ _ _ , _ _____, _ ___ _ _ _ _ _ _ _ _ _ _ _ _ 004 _ _ _ _ _ , _ _____, _ ___ _ _ _ _ _ _ _ _ _ _ _ _ : L/L LOP ENT : Enter : Edit MENU : Escape Figure 6-4 LOP display on the waypoint list 3) Press or to select waypoint number. Your display should look like one of the displays in Figure 6-5. Edit=Waypoint : 001 5) Key in LOP1 and LOP2, to enable calculation. "Calculating" 6) Press appears between parentheses during the calculation. Actual LOPs replace "Calculating" upon completion of the calculation. If the conversion fails, the message "Failed in Conversion" appears for three seconds. Press the CLEAR key and reenter the right LOP1 and LOP2. Waypoint data and date and time registered appear. LC8930 : 30 50 3 58654. 3 3 8931. 2 (34° 12. 345' N 130° 23. 456' E) Mark : Cmnt : MARINE POINT : Cursor ENT : Enter : Column MENU : Escape Loran C LOP input screen Edit=Waypoint : 001 DE : 32 (9C) RED GREEN 1 A:12. 23 1 2H:24. 35 (34° 12. 345' N 130° 23. 456' E) Mark : Cmnt : MARINE POINT ABCDEFGHIJ 1, 2 ~ 9, 0 : Cursor : Column ENT : Enter MENU : Escape Decca LOP input screen Figure 6-5 LOP input screens 6-3 6. SETTING UP VARIOUS DISPLAYS 6. 3 Demo Display The demo display provides simulated operation of this unit. Own ship tracks, at the speed selected, a figure eight course, starting from position entered. All controls are operative; you may change course, enter marks, etc. 1) While pressing and holding down NU/CU ENT, turn on the power. After the test results appear, the Simulation Mode menu appears. DEMO SETTING BASE POSITION Note: When the memory is cleared while in the demonstration mode, the equipment starts up in the normal mode. _ _° _ _. _ _ _' N _ _ _°_ _. _ _ _' W SPEED 00. 00kt : Cursor ENT: Enter : Column : N/S, E/W Figure 6-6 Simulation mode menu 2) Key in latitude of initial position. to switch from 3) If necessary, press north latitude to south latitude or vice versa. to switch from 5) If necessary, press east longitude to west longitude or vice versa. 8) Press the NU/CU ENT key to start the simulation mode. MO The icon DE appears in the plotter 1, 2, and highway display. [. . . ] Checksum VTG - Course over ground and ground speed $--VTG, x. x, T, x. x, M, x. x, N, x. x, K, a*hh<CR><LF> || || | | |||| | | | | | | | | | +------- 6 | | | | | | | | +--------- 5 | | | | | | +--+----------- 4 | | | | +--+----------------- 3 | | +--+----------------------- 2 +--+----------------------------- 1 1. Checksum NOTE Positioning system Mode indicator: A = Autonomous D = Differential S = Simulator N = Data not valid The positioning system Mode indicator field shall not be a null field. AP-18 APPENDIX WCV - Waypoint closure velocity $--WCV, x. x, N, c--c, a*hh<CR><LF> | | | || | | | | | | +------- 4 | | | | +--------- 3 | | +--+----------- 2 +--+---------------- 1 1. Checksum NOTE Positioning system Mode indicator: A = Autonomous D = Differential S = Simulator N = Data not valid The positioning system Mode indicator field shall not be a null field. WPL - Waypoint location $--WPL, llll. lll, a, yyyyy. yyy, a, c--c*hh<CR><LF> || | ||| || | | | +--------- 4 || | | +------------ 3 || +-----+---------------- 2 +-----+---------------------------- 1 1. Checksum AP-19 APPENDIX XTE - Cross-track error, measured $--XTE, A, A, x. x, a, N, a*hh<CR><LF> | | | ||| | | | | | | | +--------- 7 | | | | | +----------- 6 | | | | +------------- 5 NOTE Positioning system Mode indicator: | | | +--------------- 4 A = Autonomous mode | | +------------------ 3 D = differential mode | +--------------------- 2 S = Simulator mode +----------------------- 1 N = Data not valid 1. [. . . ]