User manual FURUNO MU-170C OPERATORS MANUAL

[. . . ] OPERATOR'S MANUAL Multi-purpose LCD Display MU-170C IMPORTANT NOTICE · · · · No part of this manual may be copied or reproduced without written permission. If this manual is lost or worn, contact your dealer about replacement. The contents of this manual and equipment specifications are subject to change without notice. The example screens (or illustrations) shown in this manual may not match the screens you see on your display. [. . . ] DISP MODE EVEN: Shows the input signal with original size. FULL/EVEN/NORMAL* NORMAL: Shows the input signal with same aspect ratio. SHARPNESS** 1-10 Softens characters and lines. () *: When inputting VGA, SVGA or XGA, a circle may be displayed as an ellipse because the aspect ratio differs. In this case, select NORMAL from the DISP MODE menu item on the RGB1, 2 or DVI menus. The top and bottom on the screen are left blank, but this is normal. **: If the characters are not clear, adjust PHASE and SHARPNESS. Menu item 8 3. 2 VIDEO Setting VIDEO1, VIDEO2 and VIDEO3 screens can be adjusted independently. The picture-in-picture window for each can be adjusted similarly. Also, the size of the picture-in-picture window can be adjusted at VIDEO1 (2 or 3) setting menu. Picture-in-picture window Picture-in-picture window 1. Set to the display currently selected, at the DISP selection window. Press the MENU key to show the main menu. Press the or key to select VIDEO1, VIDEO2 or VIDEO3 as appropriate. Same items are contained on VIDEO1, VIDEO2 and VIDEO3 setting menus. RGB1 RGB2 DVI VIDEO1 5 44 31 31 31 7000K OFF OFF VIDEO2 VIDEO3 OSD SYSTEM PIP_SIZE CONTRAST R_LEVEL G_LEVEL B_LEVEL TEMPERATURE B STRETCH W STRETCH (1 ­ 10) (1 ­ 64) (1 ­ 64) (1 ­ 64) (1 ­ 64) (5500K/6500K/7000K/8000K) (OFF, 1 ­ 10) (OFF, 1 ­ 10) VIDEO1 (2 or 3) setting menu 4. Press the or key to select the item to set. Menu item PIP_SIZE Function Adjusts the size of picture-in-picture window. Available range 1 (35 mm x 27 mm) 10 (237 mm x 189 mm) 1-64 1-64 1-64 1-64 5500K/6500K/7000K/8000K OFF, 1-10 OFF, 1-10 CONTRAST Increases or decreases contrast level. (Refer to the table on page 8. ) 9 3. 3 Menu Window Setting 3. 3. 1 Adjusting the menu window The menu window can be moved and translucentized on the OSD (On Screen Display) menu. Press the MENU key to show the main menu. Press the or key to select OSD. RGB1 RGB2 DVI VIDEO1 15 37 OFF OFF OFF VIDEO2 VIDEO3 OSD SYSTEM H_POSITION V_POSITION TRANSLUCENT PIP SW TIME PIP SKIP (1 ­ 29) (1 ­ 37) (OFF/ON) (OFF, 5-20) (OFF, V1/V2/V3) CUSTOM NAME RGB1 = RGB1______ RGB2 = RGB2______ DVI = DVI_______ VIDEO1 = VIDEO1____ VIDEO2 = VIDEO2____ VIDEO3 = VIDEO3____ OSD menu 3. Press the or key to select the item to set. Menu item H_POSITION V_POSITION Function Moves the menu window horizontally. To the left () To the right () Moves the menu window vertically. [. . . ] When reattaching the filter, be sure the filters are correctly set to the holes for the intake vent. Intake vent Display unit, rear view 18 Fuse replacement The fuse in the fuse holder protects the equipment from internal fault. If the fuse blows, find the cause before replacing it. If the fuse blows again after replacement, request service. WARNING Use the proper fuse. Use of a wrong fuse can cause fire or damage to the equipment. Ship's power source 12 VDC 24 VDC Rating of fuse 10 A 5A Battery replacement The remote controller has two AA batteries. [. . . ]