User manual FUTABA 14MZ

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FUTABA 14MZ. We hope that this FUTABA 14MZ user guide will be useful to you.

Lastmanuals help download the user guide FUTABA 14MZ.


Mode d'emploi FUTABA 14MZ
Download

You may also download the following manuals related to this product:

   FUTABA 14MZ BROCHURE (2727 ko)
   FUTABA 14MZ BROCHURE 2005 (2587 ko)

Manual abstract: user guide FUTABA 14MZ

Detailed instructions for use are in the User's Guide.

[. . . ] 14MZ 14 CHANNEL RADIO CONTROL SYSTEM PCMG3/PCM1024/FM selectable INSTRUCTION MANUAL Entire Contents © Copyright 2005 1M23N14802 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Support and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Application, Export, and Modification . . . . . . . . . . . 5 Definitions of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The display returns to the preceding screen. *The same control can be assigned to multiple channels. <Linkage Menu> 59 Trim change 1. Touch the Trim button to call the Trim setup screen. The following items can be set at the Trim setup screen. Hardware setting (Selection of switch, etc. which controls trim) (The select screen is called by touching the [H/W Select] button. ) Rate setting Operation step setting Trim mode setting Normal mode: Normal trim (parallel shift trim) operation ATL mode: ATL operation mode. CTRM mode: Maximum change near center by center trim operation Separate/combination mode: Trim data are set to flight conditions Separate mode: Trim adjustment for each flight condition Return to Linkage Menu Return to last page (The display screen is an example. The screen depends on the model type. ) 60 <Linkage Menu> Sub-Trim Setting of neutral position of each servo. The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. When you begin to set up a model, be sure that the digital trims are set to their center position. Touch the [Sub Trim] button in the Linkage Menu to call the setup screen shown below. Return to Linkage Menu (The display screen is an example. The screen depends on the model type. ) Sub trim adjustment 1. Touch the trim display part of the channel you want to adjust. Adjustment buttons appears on the Sub Trim menu screen. Use the adjustment buttons to adjust the sub trim. Initial value: 0 Adjustment range: -240~+240 (steps) *See above 3. Repeat this step for each channel. <Linkage Menu> 61 Servo Reverse Use to reverse the throw direction. Servo Reverse changes the direction of an individual servo's response to a control stick movement. For CCPM helicopters, be sure to read the section on Swash AFR before reversing any servos. With CCPM helicopters, always complete your servo reversing prior to any other programming. If you use pre-built Airplane/Sailplane functions that control multiple servos, it may be confusing to tell whether the servo needs to be reversed or a setting in the function needs to be reversed. See the instructions for each specialized function for further details. Always check servo direction prior to every flight as an additional precaution to confirm proper model memory, hook ups, and radio function. Touch the [Servo Reverse] button in the Linkage Menu to call the setup screen shown below. Return to Linkage Menu (The display screen is an example. The screen depends on the model type. ) Servo reversing procedure After setting up a new model, be sure to define all special menus. [. . . ] *The point is deleted. (Line curve) (Spline curve) (Rate adjustment buttons) The curve can also be offset horizontally in the vertical direction. [Offsetting the curve horizontally in the vertical direction] 1. Use the adjustment buttons to move the curve horizontally up and down. *Initial value: +0. 0% <Data> 125 Switch selection method The various functions used in the T14MZ can be selected by switch. The switch (including when stick, trim lever, or VR are used as a switch) setting method is common to all functions. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FUTABA 14MZ

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FUTABA 14MZ will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag