User manual FUTABA 2PC

[. . . ] Thank you for purchasing a Futaba 2PC / 2PCKA. Before using your 2PC / 2PCKA, read this manual carefully and use your R/C set safely. After reading this manual, store it in a safe place. APPLICATION, EXPORT, AND RECONSTRUCTION 1. The product described in this manual is subject to regulations of the Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes. [. . . ] If the engine is running or the motor is connected while adjustments are made the model may run out of control. Remove the main battery source from electric powered models when they are not being used. Should you accidently leave the receiver switch on the model could run out of control. Caution Do not touch Do not touch the engine, motor, speed control or any part of the model that will generate heat while running. Touching hot parts will result in serious burns. Storage And Disposal Safety Precautions Warning (When using a Ni-cad battery to power your system) At the end of a days operation store the system with Ni-cad battery discharged. Be sure to recharge the system before it is used again. You should fully discharge your systems batteries periodicity to prevent a condition called "memory". For example if you only make two run in a day or you regularly use a small amount of the batteries capacity, the memory effect can reduce the actual capacity even if the battery is charged for the recommended amount of time. Prohibited Do not throw a Ni-cad battery into a fire. Do not disassemble or attempt to repair a Nicad battery pack. Overheating, damage and acid leakage may lead to burns, loss of eye sight as well as numerous other types of injuries. The electrolyte in Ni-cad batteries is a strong alkali. Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub, wash immediately with water, seek medical attention at once. If electrolyte comes in contact with your skin or clothes, wash with water immediately. Caution Prohibited Do not store your R/C system where it will be exposed to the following conditions. · Extreme heat or coldness · Exposed to direct sunlight · Where humidity is high · Where vibration is prevalent · Where dust is prevalent · Where there is steam and condensation · Where the system would be exposed to engine exhaust Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation. (When using a Ni-cad battery to power your system) Caution When disposing Ni-cad batteries, cover any exposed contacts with some type of insulation to prevent short circuit. Some states require special handling when Ni-cad batteries are disposed. Contact the State Agency responsible for recycling hazardous waste for the procedures in your state. Other Safety Precautions Caution When operating two or more models at the same time, have a third person act as a spotter. They will be in charge of safety and you should follow their instructions. Beginners should receive instructions regarding safety and operation from an experienced modeler. Use genuine Futaba parts only. Always use only genuine Futaba receiver, servos, electronic speed controls along with other optional parts and components. Futaba will not be held responsible for damages caused by other than genuine Futaba parts and components. Use only genuine Futaba parts and components listed in the instruction manual and catalog. (When using a Ni-cad battery to power your system) Prohibited Do not short circuit the Ni-cad battery terminals. Short circuiting the terminals will lead to sparks and overheating and could cause a fire and burns as well. Safety Precautions 2PC / 2PCKA Before Operation System Contents After opening the container, check the contents for the following items. the contents will vary with the system purchased. System with 2 Servos Transmitter Receiver System with 1 MC210CB and 1 Servo System with 1 MC310CB and 1 Servo T2PC or T2PCKA (x1) R122JE (x1) S3003 (x2) S3003 (x1) MC210CB (x1) CSW-BN (x1) R2-BSS-N (x1) Servo mounting hardware and servo horns Mini Screwdriver Before Operation Servo E. S. C. Contact the State Agency responsible for recycling hazardous waste for procedures in your area. 1 Remove the batteries from the transmitter by sliding the cover in the direction of the arrow in the figure. 2 Remove the used batteries. [. . . ] On a gas powered model set the trim to neutral and adjust the linkage to the point where the carburetor is fully closed in accordance with the engine instruction manual. ST. TRIM TH. TRIM Throttle Trim Trim Operation and Travel Trim adjustments will effect the overall servo travel, check the brake side (backward) movement when changes are made. Carburetor Fully Closed (Drum Type) When trim movement is extreme If you use most of the trim movement to get the servo to the neutral position , recenter the servo horn closer to the neutral position and inspect your throttle linkage. (Slide Type) Description Of Functions Throttle Trim Servo Reverse This function reverses the rotation direction of the Steering and Throttle servos. ST. N R Steering N Side: Normal R Side: Reverse When the trim position deviates from the center, the deviation will be on the opposite side when the servo is reversed. SERVO REV SW Throttle N R TH. N Side: Normal R Side: Reverse (Reversing Switches) Steering ATV (Only 2PCKA) This function is used to adjust steering travel . The right side travel and left side travel can be independently adjusted. [. . . ]