User manual FUTABA 3PM-2.4G MX

[. . . ] 3PM-2. 4G MX 3-channel, FASST Radio control system for Car INSTRUCTION MANUAL 1M23N13518 R Digital Proportional R/C System Thank you for purchasing a Futaba 3PM-2. 4G MX system. Before using your 3PM-2. 4G MX system, read this manual carefully in order to use your R/C set safely. After reading this manual, store it in a safe place. Application, Export, and Modification 1. This product may be used for models only. [. . . ] After checking the trim, set the trim value to the center (0) position. DT1 Steering trim Throttle trim position position DT2 26 Initial Set-Up - Steering dual rate (DT3) check At initial set-up, steering dual rate is assigned to grip lever DT3 (upper) at the grip of the transmitter. Operate the DT3 lever and check if the D/R value displayed on the screen changes. After checking D/R, set the steering dual rate to 100%. - Throttle ATL (DT4) check At initial setting, throttle ATL is assigned to grip lever DT4 (lower) at the grip of the transmitter. Operate the DT4 lever and check if the ATL value displayed on the screen changes. After checking ATL, set throttle ATL to 100%. Steering D/R Throttle ATL position value DT3 DT4 (Set-Up Procedure When Installed In a Car) When installing the servos in a car, performing function set-up in the following order is recommended. Set the servo direction of operation using the Reverse function. (Page 49) The servo installation method and linkage direction depend on the kit. Therefore, the servo operation direction may have to be reversed relative to transmitter operation. Before installing the servo, check the operating direction and set it using the Reverse function. Set the subtrim and adjust the servo neutral point. Set the trigger travel by adjusting the throttle trigger mechanical ATL to your liking. Set EPA of each channel and adjust the servo throw (travel). (Page 30) Initial Set-Up 27 Function Map Power switch turned on Press "SEL" key to select the desired function screen. Press it for one second or more to scroll to the opposite direction. The current modulation mode and model number are displayed for about two seconds. (Initial Screen) End Point Adjuster Timer Steering Speed Model Select Steering EXP/Throttle EXP Channel Reverse ABS Function Subtrim Throttle Acceleration Channel 3 Position Brake mixing ATL Function 28 Function Map Programmable Mixing Steering D/R 4WS Mixing Trim Fail Safe Function (HRS system only) Digital trim DT1 - DT4 display The current position is displayed on the LCD screen for about two seconds when each digital trim is operated. Press "CH" key to select the next set-up screen. [ABS, BMX, PMX and 4WS] Any set-up screen can not be selected when the function is set to "off" or "inh". System Functions Turn on the power switch while pressing "SEL" key. Press "SEL" key to select the desired function screen. Press it for one second or more to scroll to the opposite direction. Model Copy Adjuster Model Reset LED Mode Selection Model Name Condition 2 Selection (displayed for about one second) Digital Trim Step HRS/PPM Select Function Select Lever Function Select Switch Press "CH" key to select the next set-up screen. Function Map 29 Functions End point adjuster/EPA Use this when performing left and right steering angle adjustments, throttle high side/ brake side operation amount adjustment, and channel 3 servo up side/down side operation amount adjustment during linkage. - Corrects the maximum steering angle and left and right steering angles when there is a difference in the turning radius due to the characteristics, etc. Maximum steering angle The EPA function basically determines the maximum steering angle of each channel. [. . . ] LED Mode Selection / LED-MD You can select your desired brightness of the pilot lamp. (Four steps) Calling the setup screen LED mode (Min. )L-1 ~ L-4(Max. ) LED mode selection 1 Use the (+) or (-) buttons to select the brightness of the pilot lamp. 2 When ending selection, turn off the power switch once before use. Functions 1. Turn on the power switch while pressing "SEL" key. 2. [. . . ]