User manual FUTABA 8FG

[. . . ] 8FG 8 CHANNEL RADIO CONTROL SYSTEM FASST-2. 4GHz Multi-ch/7-ch mode selectable INSTRUCTION MANUAL 1M23N22201 TABLE OF CONTENTS INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select the ACT mode by scrolling the touch sensor. *The display blinks. Touch the RTN button to activate the function and return to the cursor mode. Rate setting: Move the cursor to the [RATE] item touch the RTN button to switch to the data input mode. Set the rate by scrolling the touch sensor. reset to the initial value. Touch the RTN button to end adjustment and return to the cursor mode. 64 SWASH Swash AFR and linkage correction function. (helicopter only, except swash type H-1) plate as necessary during specific control inputs. compensation functions in this menu may not compensate effectively. To correct this use the point of the servos to the actual perpendicular the axis point of the compensation functions in this other functions. This compensation mixing is used to correct the pitch. This function is used to cancel the reaction that is generated by the difference in the movements of plate to for proper operation of each control using the corresponding compensation mixing. the setup screen shown below by touching the RTN button. <SensorTouchTM> Scrolling and return to the Linkage menu by touching the RTN button. The neutral point becomes the correction standard point. 50% position makes the mixing amount small. 1. Neutral point setting Move the cursor to the [POS] item and hold the pitch operation so that the servo horn is at a right angle to the linkage rod and Touch the RTN button for one second. This value indicates the servo's neutral position. After reading the neutral point, use the other correction functions to make further adjustments. 1. Move the cursor to the function you want to adjust and touch the RTN button to switch to the data input mode. Adjust the AFR rate by scrolling the touch sensor. rate is reset to the initial value. Touch the RTN button to end adjustment and return to the cursor mode. 65 example to describe mixing rate setting. Touch the RTN button to end at this position. *The sub-trim function can be used to make small 1. Compensating aileron input [AIL] Set the throttle to the lowest position. Move the aileron stick to the left and right and adjust the aileron compensation amount so that interference in the elevator or pitch direction is minimal. helicopter achieves maximum pitch. direction [DIR. ] as "-". Adjusting the aileron operation [AIL to PIT] Adjust the AIL to PIT rate so there is no binding in the elevator or pitch movement when the aileron stick is moved to the left and right. 2. Compensating elevator input [ELE] Adjust the elevator compensation amount so that the aileron or pitch direction interference when the elevator stick was moved up and down is minimal. Repeat steps 1 and 2 above, perform aileron and elevator compensation similarly at full throttle. 2. Adjusting the elevator operation [ELE to AIL]/ [ELE to PIT] Adjust the ELE to AIL and ELE to PIT rates so there is no binding in the aileron or pitch movement when the elevator stick is moved up and down. 1. Move the cursor to the "SPEED" item and touch the RTN button to switch to the data input mode. [. . . ] Switch the display to the mode you want to change by scrolling the touch sensor and then make the change by touching the RTN button. When you want to change the ON/OFF setting, use the touch sensor to move the cursor and touch the RTN button to switch to the data input mode. Switch the ON/ Off display by scrolling the touch sensor. When the RTN button is touched, the ON/OFF setting is changed. [. . . ]