User manual FUTABA 9VAP

[. . . ] It can also be used with conventional system servos, etc. in addition to S. BUS system compatible servos and gyros, etc. [. . . ] In addition, the operating mode (high-speed mode/normal mode) can be selected. * However, channel outputs 7 and 8 for conventional system operate in the normal mode even if set to the high-speed mode. CAUTION servo at conventional system use channels 1 to 6. Analog servos cannot be used. ·Theuseofanalogservosmaycauseservotrouble. ·When using analog servos, select the normal mode, and use channel outputs 7 and 8. Applicable systems: T8FG 2. 4GHz 10ch mode), TM10 (on 10ch mode), TM14 (on 8ch mode), TM8 (on 8ch mode), T10CG 2. 4GHz (on (on multi-ch mode) DATA port Link/Mode switch ·Channeloutputsforconventional system (1 to 8) ·Batteryterminal(B) ·S. BUS Port (S. BUS) 9VAP Compliance Information Statement (for U. S. A. ) LED This device, trade name Futaba Corporation of America, model number 9VAP, complies with part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesiredoperation. The responsible party of this device compliance is: Futaba Service Center 3002 N Apollo Drive Suite 1, Champaign, IL 61822 U. S. A. TEL (217)398-8970 or E-mail: support@futaba-rc. com (Support) S. BUS compatible/FASST-2. 4GHz (Multi-ch) system/8 channels/ high-speed receiver · Dual antenna diversity · Size: 0. 98 x 1. 86 x 0. 56 in. (24. 9 x 47. 3 x 14. 3 mm) · Weight: 0. 49 oz. Press and Hold Function No function To change the mode between Normal and High Speed More than 1 sec. cycle receiver While the linking isifdone, please to be linked is power and check the receiver S. BUS Servo Channel Setting Method S. BUS servo channel setting can be performed at the 9VAP receiver. 1Connecttheaccessoryshort-plugtotheDATAportof the receiver. Short-plug (accessory) LED Status Showing the CURRENT Solid as the mode changed. Red Solid = Normal Red Blink = Normal Green/Red Solid = High Green/Red Blink = Speed High Speed (Become Red after one (1) second) Please check the operation mode by observing the LED when turning on the receiver. If possible there's no FASST transmitter turned on around you in order to make firmer check. When turn on the receiver, the LED will be; ·Redwhenon"Normalmode" ·GreenandRed(makesOrange)whenon"HighSpeedmode". (Aftertwo(2)seconds, changetoRed. ) If there are some FASST transmitter turned on around the receiver, the LED may show the above status for a brief moment then changed to the status indication as shown in the "LED indication" table. 2ConnectanS. BUS servo to the conventional system Output connector 1 2 3 4 5 6 7 8 Channelsetting Mode A ModeB 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 16 * Connect the short-plug to the DATA port only when an S. BUS servo channel is set. Normally do not connect the plug. output connector(1 to 8) corresponding to the channel you want to set. LED Indication Green Solid Off Solid Blink Red Solid Solid Off Off Initializing Nosignalreception Receiving signals Receiving signals but ID is unmatched Status Link to the transmitter seconds. 1 Press and hold the Link/Modeswitchmorethantwo(2) Re-adjust the F/S position (only for TM-8) andtwo(2)seconds. 0 sec. Press and Hold With TM-8 (not included in this set) Other than TM-8 (not included in this set) No function To set the F/S Re-link(ID set) and to position(No re-link) set the F/S position Re-link(ID set) 3Turnonthereceiver. * Channel setting mode A (ch1 to 8 setting mode) or channel setting mode B (ch9 to 16 setting mode) can be set. 1 Press and hold the Link/Mode switch between one(1) 1 sec. [. . . ] Press and Hold With TM-8 (not included in this set) Other than TM-8 (not included in this set) No function To set the F/S Re-link(ID set) and to position(No re-link) set the F/S position Re-link(ID set) 3Turnonthereceiver. * Channel setting mode A (ch1 to 8 setting mode) or channel setting mode B (ch9 to 16 setting mode) can be set. 1 Press and hold the Link/Mode switch between one(1) 1 sec. More than 2 sec. * At once when turning on the receiver, the channel setting is completed in mode A. (ToswitchtomodeB, presstheLink/Mode button until the red and green LED starts to blink simultaneously. [. . . ]