User manual FUTABA CONQUEST

[. . . ] Futaba DIGITAL PROPORTIONAL RADIO CONTROL AM CONQUEST Thank you for purchasing a Futaba digital proportional radio control set. Please read this manual carefully before using your set. FEATURES OF FP-6NLK/4NL TheCONOUESTFP-6NLKand FP-4NL are 6 channel (6NLK) and 4 channel (4NL) AM proportional radio control set with a ergonomic case created as a result of the exhaustive pursuit of easier operation, newly designed sticks for smooth and positive operation, servo reversing switch for each channel, and other innovations based on the opinions and needs of many RC modelers. Please read this manual before using your new set. RECEIVER FP-R4F (4NL) ·Compact, lightweight, rugged construction. ·Three-wire gold-plated mini block connector is compatible with all Futaba servos. [. . . ] Battery cover Remove this cover when switching the servo reversing switches. Fig. 3 When the dual rate switch is ON, the servo throw can be adjusted within this ranqe with the dual rate trimmer. Elevator dual rate switch (6NLK only) This switch turns the elevator dual rate function on and off. The lower position is dual rate OFF and the upper position is dual rate ON. Elevator dual rate trimmer (6NLK only) This trimmer sets the elevator deflection angle when the elevator dual rate switch is in the ON position. It has the same functions as aileron dual rate. Power switch The upper position is ON. Level meter This level meter indicates the transmitter battery voltage. Neck strap bracket Bracket for the neck strap (optional). Extend it to its full length when using the transmitter. Handle Use this bar to carry the transmitter. Nonslip adjustable lever head The length of the lever head can be adjusted to fit the operator. Adjust to the length of your hand. Servo reversing switches Using the servo reversing switches · The left side of each switch is the normal position. · The servo reversing switches reverse the direction of operation of the servos. Elevator servo reversing switch Aileron servo reversing switch Throttle servo reversing switch Rudder servo reversing switch Fig. (6NLK ONLY) NORM --Normal REV --Reverse Lever head Lever head After linkage is complete, inspect the servos. If the direction of operation of the stick lever and the direction of operation of a servo are opposite, switch the appropriate servo reversing switch. , by turning them and Unlock lever heads in the arrow direction, and adjust the head to the most comfortable length, then lock it by turning it in the direction opposite the arrows. Fig. 4 24 Transmitter NiCad battery NT-8LP The tension of the stick lever spring can be adjusted. Charging jack Battery charge jack for built-in NiCad battery. ·CHARGING OF TRANSMITTER AND RECEIVER NI-CAD BATTERIES: Recharge the receiver and transmitter NiCad batteries as shown in Fig. Notes: 1) First, connect to TX NiCad and red lamp goes on. 2) Then connect to RX NiCad after connecting, L, E D, changes color from red to greenish red (orange) which indicates that both TX and RX NiCads are being charged. 3) In case of separate charging L, E, D, color will be; RX NiCad - Green. TX NiCad - Red. When these screws are removed, the back cover can be removed. · The tension of the spring can be ad justed by removing the transmitter back cover and turning the screw for each stick. Set the springs for the best stick feel. Rudder Aileron Elevator Fig. 5 ·Connect the charging plug of the FBC-8B charge to the transmitter charging jack, connect the 3P connector of the FBC-8B to the receiver NiCad battery (NR-4M), and plug the FBC-8B to a 117VAC outlet as shown in this figure. ·The Receiver battery can be used about 10 times at 10 minutes per flight between rechargings. When adjusting the aileron, and elevator the inside module is removed. Use a small Phillips screwdriver. Fig. 8 RECEIVER FP-R7H/R4F/R4H & SERVO FP-S38 The parts enclosed by the dotted lines must be purchased separately. [. . . ] PCS-38 S04134 139995 S02753 S91218 S02461 J55016 FGS-38 FGS-38 FGS-38 FGS-38 S02495 S02494 FSH. 6W FSH-41 AS1305 AS 1304 FPC-3M S90045 J50360 S60147 To insure prompt service, please follow the instructions given below. Charge the batteries for at least 18 hours prior to shipment. Remove the servos from their mounts and remove the foam padding from the receiver. Plugs or other modifications which interfere with factory test procedures will be returned to factory standard at your expense. [. . . ]