User manual FUTABA FP-2E

[. . . ] ·Three pin connector eliminates faulty contact and improves reliability against vibration and shock. Housing has a reverse insertion prevention mechanism. ·Special grommet simplifies mounting of the servo and has an excellent cushioning effect. ·Six special adjustable splined horns. [. . . ] ·Since the elevator stick employs a self-neutral system, install the sliding plate as shown in the figure when changing it to a ratchet system. Then remove the strong spring attached to the hook and replace it with the spring supplied as an accessory. ·When the transmitter is used with a tank, the direction of the stick can be changed 90 degrees by removing the four rudder stick mounting screws. ·To change the crystals, loosen the rear cover mounting screws, remove the rear cover, and then replace the crystal. The crystal is located at the left side of the printed wiring board. The transmitter crystal is marked (T) and the receiver crystal is marked (R). CAUTION: Frequency change has to be done under the supervision of FCC licensed personnel. Antenna Level meter (Engine control trim) The batteries can be easily loaded by inserting them four at a time from the back. Power switch Rear cover mounting screws Modification from self-neutral system to ratchet system. Elevator trim Elevator stick (engine control stick) Fig. 2 Rudder trim Rudder stick Slide in the direction of the arrow while pushing here. Install sliding plate Replace with weak spring Fig. 1 Fig. 3 The BEC mark is displayed on the front of the receiver of BEC (Battery Eliminator Circuitry) system sets with a receiver with shared power supply regulator. RECEIVER FP-R102GF AND SERVO FP-S128 Receiver crystal Fig. 4 Steering servo Receiver FP-R102GF ON OFF Throttle servo Antenna mire Switch Connect the servo and switch as shown in the figure and extend the transmitter and receiver antenna fully. Connection to this connector (1)When chassis power supply of engine or motor car is separate Red common 2P connector Wrapped with rubber band. Red common 2P connector (male pins) (Female pins) The Futaba BEC (Battery Eliminator Circuitry) system and BEC & ASP (Adjustable Safety Position) system can also use a common power supply with the conventional four penlight batteries system (separate power supply). (75MHz-OPTIONAL) (2) When motor car uses a special 8EC system chassis (common power supply specifications) Red common 2P connector Controller (Female pins) Connect to the red common 2P connector of the controller. Your NEW FUTABA Digital Proportional R/C system is guaranteed against defects in workmanship and material for 180 days from the date of purchase when the attached registration card is returned to us within ten days of purchase. This Guarantee is null and void properly handled, damaged in does not cover the replacement components damaged due to the if the R/C system has been ima crash, or tampered with and of plastic housings or electronic use of improper voltages. Red common 2P connector (3) When motor car uses an ordinary common power supply chassis When service is required, please take your equipment to your local authorized service station or ship it directly to us. · Use the rubber bands wrapped around the receiver to hold the servo and switch leads. ·After mounting is complete, recheck each part, then check the transmitting range by making the transmitter antenna as short as possible and extending the receiver antenna fully and operating the set from a distance of 20m to 30m. The movement of each servo should follow the movement of the transmitter sticks. ·The crystal can be changed from the outside of the receiver case. Always use a Futaba transmitter and receiver crystal pair as the replacement crystals. REPAIR SERVICE · When requesting repair of trouble that has occurred suddenly of from long use, describe the trouble symptoms in as much detail as possible. This will facilitate detection of the trouble point and shorten the repair period greatly. Fig. 7 · Defects caused by faulty materials or workmanship will be corrected free of charge. · This limited warranty is null and void if the set has been tampered with or disassembled. Refer to warranty statement for details. · Install the servos firmly. Install the servo to the servo tray as shown in the figure. In other cases, install the servo as described in the model manufacturer's manual. WORLD SALES & SERVICE FACILITIES Australia: Argentine: Canada: Chile: Denmark: England: Finland: Greece: Hong Kong: Italy: FUTABA SALES AUSTRALIA PTY. [. . . ] . 27 & 35MHz AM and FM Scandinavian countries . 27 & 72M H z (amonly) ·The frequency of Futaba digital proportional sets can be changed among bands (1) ~ (6) on the 27MHz band only. · However, a 27MHz band set cannot be changed to 72MHz band, and vice versa. ·Therefore, always attach the correct frequency flag to the end of the transmitter antenna. [. . . ]