User manual FUTABA FP-2PD

[. . . ] This allows operation at the best angle · Neutral adjuster. The throttle trigger throttle stroke/brake deflection stroke (back stroke) can be freely selected to match the application ·Servo reversing switch (steering and throttle) is standard Each servo can be reversed from the outside. This is extremely convenient when connecting the linkages. · Since a level meter is provided, battery consumption can be seen at a glance. [. . . ] 5 (12) Wheel tension adjuster This is a phillips head screw which adjusts the steering force of the steering wheel. · For engine cars, position 2 is recommended. · For electric cars, position 3 is recommended when equipped with reverse mechanism and position 2 is recommended when equipped with a brake and forward only (3) Steering trim Steering (rudder) trim (4) Steering rate adjuster The steering servo steering angle can be freely set as shown in Fig. 6 with a ratcheted adjuster installed which enables you to adjust steering servo travel volume to match a car to the course, even while running. Neutral (13) Power switch When set in the direction of the A mark (upper position), the switch is turned on and the pointer of the level meter deflects. (14) Level meter When the 13) power switch is set to ON, the level meter pointer should deflect to within the silver zone. If the pointer stops near the boundary between the silver and red zones, the battery is low, and the range of the radiowaves will be short. When the level meter pointer drops to the boundary between the silver and red zones, change the battery. Steering servo The steering angle can be set within this range. It screws in vertically as shown in Fig. 10. (5) Throttle trim knob (6) Throttle ATV high side trimmer ATV. . . (7) Throttle ATV low side trimmer Throttle ATV is a device which permits independent adjustment of the throttle servo left and right sides (from neutral) as shown in Fig. Install the servo to the servo tray as shown in the figure. In other cases, install the servo as described in the model manufacturer's manual. Fig. 13 · · · · A spare horn is provided. Wrap the receiver in sponge rubber and wrap rubber bands around the sponge rubber. Mount the receiver so it is not exposed to vibration, does not touch the frame, and does not move. When the receiver is installed on a board or used where it may be splashed with mud and water, place it in a plastic bag, etc. and wrap a rubber band around the open end of the bag to waterproof and dustproof the receiver. After use, remove the receiver from the bag to prevent condensation. Use the rubber bands wrapped around the receiver to hold the servo and switch leads. After mounting is complete, recheck each part, then check the transmitting range by making the transmitter antenna as short as possible and extending the receiver antenna fully and operating the set from a distance of 20m to 30m. The movement of each servo should follow the movement of the transmitter sticks. [. . . ] Binding head tapping screw 2. 6 x 8 FSH-4I 19. Pan head truss screw AT2453 890045 S50360 860099 S148 Fig. Nameplate Part name Upper case Middle case Bottom case Motor Motor pinion Screw 2x3 1st gear 2nd gear 3rd gear Final gear Metal bearing Potentiometer Potentiometer drive plate Seal ring Intermediate shaft 2nd shaft Servo horn D Binding head tapping screw 2. 6x8 0 ring 32. 60 Printed wiring board S129. . . . . 3PBWRB300 Neoseal sponge 5x15x15 Neoseal sponge 3x15x7 Phillips pan head screw 0 ring 1. 6 Name plate Part No. FCS-29 S91212 S05402 J50002 FGS-29 FGS-29 FGS-29 FGS-29 S04134 139995 S02753 S90415 S04287 S01351 FSH-6W FSH-41 S90420 AS 1206 FPC-8M S90336 S90333 J50400 S90410 S80702 Fig. [. . . ]