User manual FUTABA FP-7FG

[. . . ] 9 ·STICK MECHANISM AND ITS ADJUSTMENT . 9 ·RECEIVER, SERVO, SWITCHES, AND Ni-Cad BATTERY CONNECTIONS AND USAGE PRECAUTIONS . 12 ·Futaba Digital Proportional Frequencies . 13 · FEATURES The FP-7FG was specially developed for model helicopters. [. . . ] 8 11 Rudder trim lever Rudder trimmer. *Trim lever is used for fine adjustment. The trim lever is used for neutral position adjustment or correction of the posture of the aircraft after installation is completed. However, after test flight, try to keep the neutral position as they are making necessary corrections with the rod adjusters, etc. 13 Elevator dual rate switch · Elevator dual rate ON-OFF switch. Simitar to aileron dual rate, (dual rate ON) the elevator deflection can be adjusted with the elevator dual rate trimmer 10 and the servo operating linearity can be switched with the DR <-> VTR switch 11. 14 Trainer switch Pull on/self-off switch. The transmitter connected by the trainer cord (MTC) operates and when it is OFF, your-own transmitter only operates. 15 Throttle-rudder mixing knob Ratchet knob that sets the throttle to rudder mixing amount and direction. 16 Idle-up ON-OFF switch This switch turned ON when pushed forward. is l7 and the servo operating linearity can be switched with the DR <-> VTR switch 18 . Other functions are the same as those of the aileron dual rate switch. 20 Power switch 2 1 Square level meter Level meter indicates the transmitter output power and indirectly shows power supply voltage. 22 Antenna 23 Antenna storage The opening is used for storage of the antenna while carrying the transmitter. 10 Elevator dual-rate trimmer adjusts the elevator travel when the 13 elevator dual-rate or VTR on/off switch is ON. 1 DR <-> VTR switch 1 12 Throttle hold point trimmer This trimmer sets the throttle servo stop point when the throttle hold switch 18 is set to ON. When the trimmer is turned counterclockwise, the throttle servo moves to the stow side. 13 Throttle high side ATL trimmer This trimmer adjusts only the high side of the throttle stick. It is extremely convenient when connecting the linkage, since the low side remains unchanged even when the throttle high side is adjusted with this trimmer. 20 Pitch control high side trimmer 19 Pitch control low side trimmer High pitch can be adjusted within this range. Low pitch can be adjusted within this range. Pitch control servo Fig. 13 21Throttle -> Pitch control mixing ONOFF switch This switch turns mixing from the throttle control (channel 3) to the pitch control (channel 6) ON and OFF. 22 Servo reversing switches These switches reverse the direction of the servos. It is very convenient when connecting the linkage. 43 CH7 lever channel 42 CH6 pitch control 41CH5 switch channel Transmitter RF module Change this module to switch to any frequency among 27, 29. 53 & 72 MHz bands. Transmitter I 6 37 Aileron 38 Elevator [39] Throttle 40 Rudder NORM: Forward REV: Reverse Remove the module by pulling it forward while pressing this tab inward. Fig. 15 CHARGING OF TRANSMITTER AND RECEIVER Ni-Cad BATTERIES: Recharge the receiver 8 AC-110V (220V, 240V) and transmitter Ni-Cad batteries as shown in Fig. CH7 servo Pitch control servo (Landing gear servo) Received crystal Landing gear adapter (Landing gear servo) 10 FP-R107M 7 channel FM receiver Rudder servo When a rate gyro is used, this servo connects to the receiver through the rate gyro. Antenna Extension cord Throttle servo R4-SWJ Elevator servo Aileron servo Charging plug Fig. 20 Rate gyro FP-G152 Connected servo (rudder servo for helicopter) neutral position trimmer (This trimmer is operative even when the control box power switch is set to OFF. ) Connect to receiver retract or auxiliary channel (for gyro sensitivity switching) Remove these screws. [. . . ] Arm 3 shift 4. 8° to the right, arm 6 shifts 2. 4° to the left, and arm 4 shifts 7. 2° to the right and left. Fig. 25 12 horn A (FSH-6X) horn B (FSH-6S) horn C (FSH-6R) horn D (FSH-6W) Fig. 26 Futaba Digital Proportional Frequencies (FOR U. S. A. ) ·The frequency of Futaba digital proportional sets can be changed among bands (1)~(6) on the 27MHz band only. ·However, a 27MHz band set cannot be changed to 72MHz band, and vice versa. [. . . ]