User manual FUTABA FP-7UAFS

[. . . ] 4 channels --Elevator -> f l a p mixing --Flaperon & aileron differential -Programmable mixing 2 separate systems --Flap -> elevator mixing · TABLE OF CONTENTS SET CONTENTS . 3-5 DISPLAY FUNCTIONS NORMAL DISPLAY MODE . 7 FUNCTIONS AND DATA SETTING ADJUSTABLE TRAVEL VOLUME . 8 EXPONENTIAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] display to (F/S function setting) When interference makes reception impossible, the servos move to the position set at the transmitter. When the interference ceases, the F/S function is reset. The channel or for which the F/S function was selected is held in the desired position. At the same time, data is automatically sent to the receiver. ) *The F/S set data is automatically sent every minute. *The PPM mode does not have an F/S function. (FP-7UAFSS) *When using the B. F/S function, set the throttle channel F/S function. To PMX1 -10- · FUNCTION AND DATA SETTING Press the [MODE SELECT] To normal display mode PMX1 PROGRAMMABLE MIXING 1 This mixing is useful in correcting bad tendencies of the aircraft and in making operation more pleasant. · Mixing of any two channels is possible. · The left and right (up and down) mixing rate can be set independently. · Setting range: 0 -- 100% (mixing maximum) Mixing activate/inhibit mode setting Set the mode with the keys. + : Activate --: Inhibit Master channel selection (INH: Inhibit state) Set the flashing display to the mark with the keys. Select the channel to be set with the keys. Activate state ON: OFF: ON OFF Slave channel selection Set the flashing display to the mark with the keys. Select the channel to be set with the keys. Mixing servo direction of operation setting Set the flashing display to "+" (or "--") with the keys. (When the + and -- keys are pressed simultaneously, 50% is set. ) Set a different elevator direction by repeating steps and OFF side To 6 - > 2 13 - · FUNCTION AND DATA SETTING Press the [MODE SELECT] To normal display mode 6-2 FLAP -> ELEVATOR MIXING Use this mixing when an air brake is necessary when landing or diving, etc. during flight. Activate/inhibit mode setting Set the mode with the keys. + : Activate -: Inhibit Elevator servo throw setting (INH: Inhibit state) Set the flashing display to the channel 2 with the keys. (When the + and -- keys are pressed simultaneously, 0% is set. ) · The operating position of the elevator and flap servos can be set. Flap servo throw setting Set the flashing display to chanwith the nel 6 keys. (When the + and -- keys are pressed simultaneously, 0% is set. ) OFF side ON side ToSNP -14 - · FUNCTION AND DATA SETTING Press the [MODE SELECT] To normal display mode SNP SNAP-ROLL Activate/inhibit mode setting Set the mode with the keys. + : Activate -: Inhibit Avalanche and other snap rolls can be performed by switch. R/U: R/D: L/U: L/D: snap roll directions can be Right up snap Right down snap Left up snap Left down snap Select the direction UP RIGHT DOWN LEFT the to the combination of directions to be set. Switch Aileron servo throw setting Set the flashing display to CH1 with the keys. (When the + and -- keys are pressed simultaneously, 100% is set. ) · The throw of the channel 1 (aileron), channel 2 (elevator), and channel 4 (rudder) servos can be set. (Mode in which operation is not performed when the landing gear is down even if the switch is turned on by mistake. ) "1" to "4" is displayed according to the position. 1: R/U 2: R/D 3: L/U 4: L/D Elevator servo throw setting Set the same as Rudder servo throw setting Set the same as Set for each direction of the by repeating steps to SAFETY mode setting Set the to CH5 with the keys. Set the to the direction for which snap roll is to be turned off (direction in which landing gear is down). UP RIGHT Press the -- side of the keys. SNAP ROLL DOWN LEFT F: SAFETY mode released 5L: SAFETY mode set and ON 5F: S A F E T Y mode set and OFF SAFETY mode release Set the to CH5 with the keys. Press the + side of the keys. ToDIFF - 15 -- · FUNCTION AND DATA SETTING Pressthe (MODE SELECT] keys simultaneously To normal display mode DIFF AILERON DIFFERENTIAL Activate/inhibit mode setting Set the mode with the keys. + : Activate -: Inhibit A left and right differential can be applied to the ailerons. [. . . ] Setting method Always turn off the student transmitter power switch. Do not operate the trainer switch either. *Use the functions of the other two transmitters with the same setting. · SPLINED HORNS This horn permits shifting of the servo neutral position at the servo horn. Setting and shifting the neutral position. [. . . ]