User manual FUTABA R6008HS

[. . . ] R6008HS/R6014HS Thank you for purchasing the R 6 0 0 8 H S, R6014HS FASST receiver. These models have two(2) operation mode as shown below. [. . . ] By doing this step, the mode can switch over between two(2) modes. Turn on the receiver. To change the mode between Normal and High Speed Re-adjust the F/S position (only for TM-8) 1 Press and hold the Link/Mode switch between one(1) and two(2) seconds. 0 sec. More than 2 sec. Press and Hold time With TM-8 (not included in this set) With TM-10, TM-14 (not included in this set) No function To set the F/S Re-link(ID set) and to position(No re-link) set the F/S position Re-link(ID set) No function TM8(on 8ch mode), TM10(on 10ch mode), TM14(on multi-ch mode) Usage condition on "High Speed mode" from 6ch accept Outputsservos1ch toor most typethe digital only of peripherals. · If any analog servos connected to these output CAUTION as it will cause malfunction. Please check the peripherals if there's any malfunction with whole stick lever throw. If any malfunction occur please change the operation mode to "Normal mode. " · Output of other channels shown below allow to use any type of servos. R6008HS - 7ch and 8ch R6014HS - 7ch to 12ch, DG1, DG2 linking procedure Do not perform thewire is connected with motor's main or the engine is operating as it may result in serious injury. the linking is please While receiver power done, check if cycle and the receiver to be linked is really under the control by the transmitter to be linked. WARNING Function No function LED Status Showing the CURRENT Solid as the mode changed. Red Solid = Normal Red Blink = Normal Green/Red Solid = High Green/Red Blink = Speed High Speed (Become Red after one (1) second) Link/Mode Switch Please check the operation mode by observing the LED when turning on the receiver. If possible there's no FASST transmitter turned on around you in order to make firmer check. When turn on the receiver, the LED will be; · Red when on "Normal mode" · Green and Red (makes Orange) when on "High Speed mode". (After two(2) seconds, change to Red. ) MPDX-1 application(R6014HS only) When to use the MPDX-1, please prepare the exclusive short-plug shown below. Short-plug (sold separately) R6008HS LED LED R6014HS Link/Mode Switch If there are some FASST transmitter turned on around the receiver, the LED may show the above status for a brief moment then changed to the status indication as shown in the "LED indication" table. Please insert the short-plug to R6014HS's "DATA" port. Short-plug LED Indication Compliance Information Statement (for U. S. A. ) R6008HS/R6014HS Specifications Green Solid Off Solid Blink Red Solid Solid Off Off Initializing No signal reception Receiving signals Receiving signals but ID is unmatched Status This device, trade name Futaba Corporation of America, model number R6008HS/R6014HS, complies with part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesiredoperation. [. . . ] · Please note that when the short-plug is plugged to the "DATA" port, both CH11 and CH12 become acceptable for MPDX-1. CH11 or CH12 can not separately set as the "MPDX-1-ready-output. " Link to the transmitter than two(2) seconds. 1 Press and hold the Link/Mode switch more FUTABA CORPORATION Phone: (043) 296-5118 Facsimile: (043) 296-5124 Makuhari Techno Garden Bldg. , B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan 1M23N17413 ©FUTABA CORPORATION 2009, 01 (1) [. . . ]