User manual FUTABA S5801

[. . . ] FHSS 3PL 2. 4GHz system · 2. 4GHzSS (Spread Spectrum) radio communication system · Frequency channel setting unnecessary: Sifting the channels within the 2. 4GHz band automatically, this system minimizes the interference from other 2. 4GHz system. · Accepts no unwanted signals by using ID code · Built-in antenna (TS5801 transmitter) Application, Export, and Modification 1. This product may be used for models only. It is not intended for use in any application other than the control of models for hobby and recreational purposes. [. . . ] Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub, wash immediately with water, and seek medical attention at once. If electrolyte comes in contact with your skin or clothes, wash with water immediately. Do not leave the radio system or models within the reach of small children. A small child may accidentally operate the system. This could cause a dangerous situation 6 Safety Precautions and injuries. NiCd batteries can be very dangerous when mishandled and cause chemical damage. CAUTION Do not store your R/C system where it will be exposed to the following conditions. Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation. If the system will not be used for a long period of time, remove the batteries from the model and store in a cool, dry place. If the batteries are left in the model, electrolyte may leak and damage the model. <NiCd Battery Recycling> A used NiCd battery is valuable resource. As such, the antenna (arrow direction) should not be pointed directly at the model. Throttle Trim Lever (DT2) (*1) Adjusts the throttle in small increments so the model will not move at neutral. LCD screen Power switch turned on: Beep confirmation sound is generated and the model name is displayed for about two seconds and then the initial screen appears. (Initial screen) y number display y voltage display Antenna (Built-in) The antenna is inside of this part. Select Button Power Switch When slid upward, the power is turned on. Press the Select button to select the desired function screen. Steering Wheel Turn model to left or right. Channel 3 Switch Turn channel 3 servo to left or right. Throttle Trigger Control the speed of the model and movement forward and backward. Steering Dual Rate Lever (D/R) Grip Handle Adjust the vehicle's steering sensitivity across the entire range. (*1) (*1) Digital trim DT1, DT2, and D/R operation Push the lever to the left or right (up or down). MC230CR or MC330CR is used. Connects to Motor Connects to Battery E. S. C. Power Switch (CH4) (CH2) Channel 4 Servo (CH3) Channel 3 Servo Receiver (CH1) Steering Servo Gas Powered Model (CH4) Channel 4 Servo (CH3) Channel 3 Servo (B) Receiver To Receiver Battery (CH2) Throttle Servo Power Switch (CH1) Steering Servo Receiver Antenna Installation Install the R2004GF receiver on the car as follows: Note: The operating range may become shorter, depending on where the receiver and the antenna are mounted. Antenna Antenna tube WARNING Install the antenna in the higher place as shown in the figure. Keep the antenna as far away from the motor, ESC and other noise sources as possible. Put the antenna in the antenna tube to protect it. Doing so causes damage. Coaxial cable R2004GF 12 Assembly / Adjustment Assembly Precautions WARNING Check the receiver, servos, and battery connectors, to be sure they are firmly connected. If a connector is not fully inserted, vibration may cause the connector to work loose while the model is operating. Operate each servo horn over its full stroke and check to see that the linkage does not bind or is not too loose. Excessive force applied to the servo horn by binding or poor installation may lead to servo problems and result in loss of control. (Electric Cars and Boats) Isolate the receiver from vibration by attaching to the chassis or mounting plate with thick double sided tape. (Gas Powered Cars and Boats) Isolate the receiver from vibration by wrapping it in foam rubber or similar type cushioning material. Protect the unit from water damage by placing it in a plastic bag or waterproof radio box. The receiver contains precision electronic parts. [. . . ] Setting example: Throttle idle or brake position To Initial Screen Function Map 23 Reference *Specifications and ratings are subject to change without prior notice. Ratings Communication method: One-way operation system Maximum operating range: 80m (Optimum condition) For safety: F/S (Throttle), ID (About 4 billion ways of pair identifications) Servo S3050 (Standard digital servo) Power requirement: 6V (common with receiver) Current drain: 8mA (at 6V / Idle) Output torque: 6. 5kg-cm (90. 3oz. -in. ) at 6V Operating speed: 0. 16sec/60 degree at 6V Size: 40. 0x20. 0x38. 1mm (1. 57x0. 79x1. 50in. ) Weight: 49g (1. 72oz. ) Transmitter TS5801 (FHSS system, wheel type, 3+1 channels) *The 4th channel is used for mixing functions only. Transmitting frequency: 2. 4GHz band Power requirement: (Dry cell battery) Penlight x 4(6V) Current drain: 100mA or less Transmission antenna: 1/2 di-pole (Built-in) E. S. C. MC230CR / MC330CR (Electronic speed control) Operating system: Forward, reverse, and brake operations are all linear. Power requirement: Nicd battery 6-7 cells (7. 2 to 8. 4V) PWM frequency: 1. 5kHz (fixed) Setting: One-touch input by pushbutton switch. [. . . ]