User manual FUTABA SBD-1

[. . . ] S. BUS Decoder Before using your new SBD-1, please read this manual thoroughly and use the system properly and safely. After reading this manual, store it in a safe place. ·Channel setting by SBC-1 1 Connect the S. BUS connector of the SBD-1 2 Thank you for purchasing an SBD-1, S. BUS *1 decoder. [. . . ] Also SBD-1 can be used. to the receiver S. BUS connection port or S. BUS hub. Connect a conventional servo or an S. BUS servo to the servo connector of the SBD-1. Usage Precautions CAUTION connect any device (gyro, the state which the Do notother than servos to thebattery, Alwaysisuse in attached tointhe fuselage etc. ) servo SBD-1 firmly not connect an S. BUS Do the SBD-1 to other than connector of an S. BUS of the airplane or helicopter. There is the danger of loss of control and crashing if the connector is disconncted by vibration and shock. will not be responsible for damage caused by combination with other than Futaba Genuine parts. WARNNG * When an S. BUS servo was connected, that servo will operate as a conventional servo. However, it operates on the channel set at the servo connector of the SBD-1 instead of the channel set at the servo itself. to the receiver S. BUS connection port or S. BUS hub Conventional servo (or S. BUS servo) connector of the SBD-1. There is the danger of erroneous operation or damage. servo connection port. There is the danger of erroneous operation or damage. * (Channel confirmation) When the operation position of the channel selector switch and the channel set at the connector during the SBD-1 servo connector selection coincide, the LED changes to a steady light. 4 Set 5 Name of Each Part and Accessories (Upper) the SBC-1 channel selector switch to the channel you want to set. Hold down the setting switch (about 1 second). SX1 SX2 SX3 Meaning of Special Markings Pay special attention to safety where indicated by the following marks: S. BUS connector <Accessories> Channel No. Label SBD-1 SX1 SX2 SX3 (Middle) (Lower) DANGER WARNING CAUTION Procedures which may lead to dangerous conditions and cause death/serious injury if not carried out properly. Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out properly, or procedures where the probability of superficial injury or physical damage is high. Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if not carried out properly. ·Put the channel No. label on the servo connector fortheidentificationofchannelNo. . Instruction manual (this manual) Servo connector Channel Setting Before installing the SBD-1 to the fuselage, set each channel at each servo connector (SX1~3). [. . . ] Please contact our service center if you feel that any corrections or clarifications should be made. FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan = Prohibited = Mandatory ·Dimensions: 41. 8x12. 3x8. 4mm (1. 65x0. 48x0. 33in. ) (excluding protruding) ·Weight: 6. 9/10. 8/14. 7/24. 5/34. 3g (0. 24/0. 38/0. 52/0. 86/1. 21oz. ) ·Powerrequirement: Ni-Cd, Ni-MH 4 to 5 cells equivalentbattery(Futaba) ·O p e r a t i n g t e m p e r a t u r e range:-10to+45° [SBD-1 Ratings] 1M23N23401 ©FUTABA CORPORATION 2010, 2 (1) [. . . ]