User manual GAGGENAU AW281120

[. . . ] Gaggenau Operating and installation instruction Extractor hood AW 280190/280120 AW 281190/281120 Fig. 1 ELECTRIC 2 Table of Contents Operating Instructions Installation Instructions Operating modes Exhaust-air mode Circulating-air mode Coanda effect Operating for the First Time If you encounter a problem Safety instructions Operating procedure Intensive setting Special functions Filters and maintenance Grease filters Saturation indicator F Activated carbon filter Cleaning and care Replacing the light bulbsn 4 4 4 5 6 6 7 8 9 9 10 10 10 11 12 13 Important information Prior to installation Exhaust-air mode Circulating-air mode Preparing the wall Electrical connection Installation 15 16 16 17 18 19 20 3 Operating modes Exhaust-air mode Circulating-air mode · Installation accessories for exhaust air mode. Ventilation duct AD280/281-012 for ceiling heights of 2. 25­2. 62 m AD280/281-022 for ceiling heights of 2. 62­3. 01 m. · Installation accessories for circulating air mode. Ventilation duct AD280/281-112 for ceiling heights of 2. 36­2. 62 m AD280/281-122 for ceiling heights of 2. 62­3. 01 m. · · · The extractor-hood fan extracts the kitchen vapours and conveys them through the grease filter into the atmosphere. [. . . ] Important: By cleaning the metal grease filters at appropriate intervals, the possibility of them catching fire as a result of a build-up of heat such as occurs when deep-fat frying or roasting is taking place, is reduced. Removing and inserting the metal grease filters: IMPORTANT: The lighting must be switched OFF and cool. 1 Press the catch on the grease filters inwards and fold the filters down. At the same time take hold of the underside of the grease filters with your other hand. Saturation indicator: F The grease filter saturation display F flashes after an operating time of 30 hours to you indicate to you that you should clean the grease filter. The grease filters can of course be cleaned at any time, even if the grease filter saturation display has not started to flash. 2 3 4 Clean the filters. Insert the clean filters back into the hood. ­ Press the button F. Cleaning the metal grease filters: · · · In normal operation (1 to 2 hours daily), the metal grease filter must be cleaned 1 x a month. The filters can be cleaned in a dishwasher. It is however possible that they will become slightly discoloured. The filter must be placed loosely, and NOT wedged, in the dishwasher. Important: Metal filters that are saturated with grease should not be washed together with other dishes etc. · When cleaning the filters by hand, soak them in hot soapy water first of all. Do not use aggressive, acidic or caustic cleaners. Then brush the filters clean, rinse them thoroughly and leave the water to drain off. 10 Activated carbon filter For neutralizing odours in recirculating mode. Caution: As the filter becomes more and more saturated with grease, there is an increased risk of fire and the function of the extractor hood may be impaired. Important: Change the activated carbon filter promptly to prevent the risk of fire from the accumulation of heat when deep-fat frying or roasting. Installation and removal: IMPORTANT: The lighting must be switched OFF and cool. . 1 2 Remove the metal-mesh filters (see "Removing and inserting the metal-mesh grease filters"). Even after a while, there is still a risk of being burnt. 2 3 4 Remove the metal-mesh filters (see "Removing and inserting the metal-mesh grease filters"). Loosen the screws for the mounting rails. . Carefully remove the glass panes. 5 Remove the sockets for the fluorescent light bulbs. 6 Replace the fluorescent light bulbs with new ones available commercially (36 W, 840 Cool White, socket 2 G 11). Risk of breakage! 13 7 8 9 Insert the sockets for the fluorescent light bulbs. [. . . ] If the earthed socket is no longer accessible following installation of the extractor hood, ensure that there is a permanently installed disconnector. If it is necessary to wire the extractor hood directly into the mains: The extractor hood should only be connected to the electricity supply by a properly qualified electrician. A separator must be installed in the household circuit. A suitable separator is a switch that has a contact gap of more than 3 mm and interrupts all poles. Such devices include circuit breakers and contactors. [. . . ]