User manual GAGGENAU VC422610

[. . . ] Operating and Assembly Instructions VC 422-610 Glass Ceramic Electric Cooktop VC 422-610 Important safeguards 1. Important Notes For your safety Operating for the first time About use 2. Features Features Special accessories Visual signals 3. Operation Switching on and off Indicator light / Residual heat display Cooking zone extension Holiday safeguard 4. [. . . ] This will eliminate any 'newness' smells and soiling (see chapter "Cleaning and care"). About use The appliance is intended solely for household use and must not be put to any other uses. Use the appliance to prepare meals only. Do not use the appliance to heat up the room in which it is installed. Do not use the cooking surface to store items. Place a cooking vessel on the corresponding cooking zone before operating it. Do not remove the cooking vessel until you have switched off the hotplate. The size of pots and pans should correspond to the size of the hotplate. Iridiscent discoloration can be caused by the bases of some pots. These do not interfere with the operation of the glass ceramic hob. Always keep the cooking area dry and clean. The surface can be scratched due to dirt (e. g. Never heat food in aluminium or plastic containers as the material can melt and damage your hob. Built-in overheating protection prevents overheating of the appliance and of surrounding kitchen furniture. In the event of malfunction, first check your household fuses. If the power supply is in proper working order, but the appliance is still not functioning, please inform your specialist dealer or your nearest Gaggenau after-sales service. 6 2. Features Features 1 SuperQuick cooking zone Ø 5 3/4 ´ ´ (1100 W), converts to roasting zone 5 3/4 ´ ´ x 9 1/2 ´ ´ (2000 W) 1 2 SuperQuick cooking zone Ø 7 ´ ´ (1500 W), converts to Ø 9 ´ ´ (2400 W) 3 Display panel with indicator light and residual heat display 4 Control knob for front cooking zone 3 4 5 5 Control knob for rear cooking zone 2 Special accessories You can order the following special accessory: VV 400-000 Connecting trim VZ 400-700 Connecting trim with timer VD 400-000 Appliance cover 7 Visual signals Luminous disc Indicator behind the on the control knob cooker lights OFF light constantly slow flashing of indicator light (long OFF short ON) , fast flashing of a luminous disc cooking zone ON residual heat display Signification Cause / Remedy appliance is switched OFF normal use The appliance is too hot to be touched safely. holiday safeguard The appliance setting has not been changed for over 4 hours. Turn control knobs to 0 and then switch on again if required. power cut After a power cut, the appliance stays switched off for safety reasons. Turn control knobs to 0 and then switch on again if required. Connecting cable between the appliance and the control panel is not plugged in. Check that cable is plugged in firmly. fast flashing of both control knobs fast flashing of both luminous discs alternately faulty installation 8 3. Operation Switching on Switching on Press down the control knob for the corresponding cooking position and turn it left or right to the required position (1 -12). [. . . ] The appliance must be properly grounded. Pay attention to the information on the rating plate. 16 The minimum spaces that must be maintained between the appliance cooking surface and the horizontal surface above the cooking top shall be: 2 A 1 3 5 1 Building back wall 2 Top building cabinet 3 Cooking surface 4 Building side wall 5 Building side wall 4 A = 30 inches (762 mm) minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet; or A = 24 inches (600 mm) minimum when bottom of wood or metal cabinet is protected by no less than 1/4-inch-thick flame-retardant millboard covered with no less than No. 28 MSG sheet steel, 0. 015inch-thick stainless steel, 0. 024-inch-thick aluminimum, or 0. 020-inch-thick copper. 17 Preparing the cabinet 1 1/32'' 12/32'' 13/32'' 14 31/32'' 5 4' 20 /6 8 3' 21/32' 5 1/2' ' 1 11 /32 · Cut out the recess for the hob in your worktop. Proceed as indicated on the installation sketch. [. . . ]