User manual GAI-TRONICS 7245-005 INDOOR REMOTE SUBSET AMPLIFIER ENCLOSURE

[. . . ] 42004-684L2B Page: 2 of 9 The Model 723-005 or -905 Remote Amplifier is designed only for use with the magnetic hookswitch subsets listed in the System Requirements section of this manual. Subsets containing an RF hookswitch are not supported. In order to provide Page/Party® features, the amplifier enclosure must be connected to a Model 723-005 Remote Subset Amplifier. Figure 1. Model 7245-005 Outline Detail f:\standard ioms - current release\42004 instr. [. . . ] This enclosure should be mounted within reach of these cables. The recommended torque setting for securing the amplifier to the enclosure is 10 to 12 in-lbs. or 1. 13 to 1. 36 n-m. f:\standard ioms - current release\42004 instr. manuals\42004-684l2b. doc 11/10 Model 7245-005 Indoor Remote Subset Amplifier Enclosure Pub. Typical Desk-edge Installation Figure 4. Typical Flush-mount Installation Mounting and Wiring Instructions 1. The indoor enclosure is not supplied with openings for conduit or cable because their locations vary with each installation. Drill or punch these openings using the supplied template before mounting the enclosure. The best location for the conduit holes is along the top or bottom of the enclosure and near the rear surface. Avoid the top center and bottom left because of possible interference with the plug-in amplifier receptacle and the subset receptacle. Sealed threaded hubs, such as Myers "Scru-tite" are recommended conduit terminations. Four 0. 312-inch (7. 92 mm) diameter mounting holes located in each corner of the amplifier enclosure have been provided for installing the enclosure. Place the enclosure on the mounting surface and secure it with four screws. Feed the system wiring into the enclosure. Strip the insulation on each conductor of the system cable. Install a ring lug on the ground conductor (GRN/YW wire) and spade lugs on all other conductors. Terminate each conductor using the wire colors indicated in the system wiring diagrams in Figure 3 and Figure 4. NOTE: Improper terminations may diminish the station performance. Feed the speaker wiring into the enclosure. Strip the insulation on each conductor of the speaker cable. Connect the speaker wires of an 8-ohm speaker between the TB1-4 (speaker common) and TB1-5 (8-ohm) or connect the speaker wires of a 16-ohm speaker between the TB1-4 (speaker common) and TB1-6 (16-ohm). Set the speaker muting control to the desired location. [. . . ] The applicability of any such third-party warranty will be determined by GAI-Tronics. Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors, shall be performed in accordance with the standard of care with which such services are normally provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided any and all issues are identified prior to the demobilization of the Contractor's personnel from the work site. Re-performance of services shall be Buyer's sole and exclusive remedy, and in no event shall GAITronics warranty obligations with respect to services exceed 100% of the total cost of the services provided hereunder. Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty periods as set forth above. Provided, however, that if the defect complained of is latent and not discoverable within the above warranty periods, every claim arising on account of such latent defect shall be deemed waived unless it is made in writing within a reasonable time after such latent defect is or should have been discovered by Buyer. Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent caused by Buyer's neglect, failure to follow operational and maintenance procedures provided with the equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the equipment. [. . . ]