User manual GARMIN FISHFINDER 100 BLUE

[. . . ] Fishfinder 100 Blue owner's manual © 2001 GARMIN Corporation GARMIN International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U. S. A. 913/397. 8200 or 800/800. 1020 Fax 913/397. 8282 GARMIN (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9AQ, U. K. [. . . ] Highlight the `Chart' tab on the Setup Menu. Highlight the `Scale' selection field and press ENTER. Choose `Overlay, ' `Corners, ' `Basic' or `No Scale, ' then press ENTER to accept the selection. Scale -- `Overlay' Scale -- `Corners' Scale -- `Basic' Scale -- `No Scale' 18 Tools Tab The `Tools' tab contains the `Flasher, ' `Simulator' and `Noise Reject' tools. The `Noise Reject' and `Flasher' tools are used to enhance the chart and help in identifying and providing information about an underwater return. The `Simulator' tool is used to enhance the simulator mode by allowing you to customize the simulated transducer selection. To access the `Tools' tab, place the highlight over it using the arrow keys. Flasher Unit Operation Setup Menu: Tools Tab With the `Flasher' tool active, a graphic Flasher representation will be displayed on the far right side of the chart. This graphic Flasher displays structure and bottom returns much the same as a true Flasher. You may find this feature particularly useful when using `Fish Symbols. ' To Turn the Graphic Flasher on and off: 1. Highlight the `Tools' tab on the Setup Menu. Highlight the `Flasher' selection field and press ENTER. Select `On' or `Off' and press ENTER to accept the selection. Graphic Flasher Activated Simulator The `Simulator' tool allows you to select a simulated transducer type for use with the Fishfinder 100 Blue's built-in display simulator. These choices allow the simulator to more accurately depict actual operation of the unit. For details on using the simulator, see page 35. Noise Reject The `Noise Reject' tool helps filter unwanted noise from the chart. The `Noise Reject' tool can be turned `Off, ' set for `Auto' (automatic) adjustment or set for `Manual' adjustment. Continued on page 20 Remember when setting the Noise Reject tool, the higher the noise rejection setting, the more likely the unit is to not show fish or structure. 19 Noise Reject (continued) Unit Operation Setup Menu: Tools/Numbers Tabs To change the Noise Reject Setting: 1. Highlight the `Tools' tab on the Setup Menu. Highlight the `Noise Reject' selection field and press ENTER. Choose `Off, ' `Auto, ' or `Manual' and press ENTER. To manually adjust the Noise Reject Setting: 1. Select `Manual' in the `Noise Reject' field of the `Tools' tab of the Setup Menu, then press ENTER. A slider will appear below the `Noise Reject' selection field. Use the UP/DOWN Arrows to highlight the slider, then press ENTER. Use the LEFT/RIGHT Arrows to manually adjust the Noise Reject Slider to the desired setting, then press ENTER. Noise Reject Manual Adjustment Slider Numbers Tab The `Num' (Numbers) tab allows you to choose whether you would like to see normal or large numbers on the chart. You can also configure the unit to display `Battery Voltage, ' (water) `Temperature, ' and `Speed' Over Water if the unit is equipped with capable sensors. [. . . ] 7 System Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26 L Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii M Memory Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Mounting the Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8 Mounting the Speed Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Mounting the Transducer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 N NMEA Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Noise Reject . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20 Number Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Numbers Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]