User manual GARMIN G1000 BEECHCRAFTBARON58 G58 PILOTS GUIDE

[. . . ] G1000 TM Pilot's Guide for Beechcraft 58/G58 Part Number 190-00629-00 Rev. B Change Summary Corrected figure numbering sequence in Section 7 Record of Revisions Revision Date of Revision Revision Page Range A 10/18/05 ------------B 11/09/05 All Description Initial release Garmin G1000 Pilot's Guide for Beechcraft 58/G58 190-00629-00 Rev. B COPYRIGHT Copyright © 2005 Garmin Ltd. This manual reflects the operation of System Software version 0500. 01 or later. [. . . ] The pilot can also create and insert a user waypoint by pointing at a blank spot on the nav map and pressing `LD WPT'. This creates a user waypoint at the map cursor and inserts it into the flight plan. 5. 3. 7-68 Garmin G1000 MFD Pilot's Guide for the Beechcraft 58/G58 190-00629-00 Rev. B MULTI FUNCTION DISPLAY VERTICAL NAVIGATION (VNAV) PAGE The Vertical Navigation Page allows the creation of a three-dimensional profile which guides the aircraft from it's present position and altitude to a final (target) altitude at a specified location. This is helpful when you would like to descend to a certain altitude near an airport or climb to an altitude before reaching a route or Direct-to waypoint. Once the profile is defined, message alerts and additional data on the Navigation Map Page keep the pilot informed of progress. NOTE: An active flight plan or Direct-to must be entered in order to utilize VNAV. NOTE: To display terrain or topo data on the Vertical Navigation Map Page, press the MAP softkey. Press the TOPO, TERRAIN, or LTNG softkey. Press the same softkey to remove the displayed data from the Vertical Navigation Page. To create a vertical navigation profile: 1. Press the FMS knob to activate the cursor. Figure 7-51 Vertical Navigation (VNAV) Page 190-00629-00 Rev. B Garmin G1000 MFD Pilot's Guide for the Beechcraft 58/G58 7-69 MULTI FUNCTION DISPLAY 3. With the `TARGET ALTITUDE' field highlighted, turn the small and large FMS knobs to select the target altitude and press the ENT key. Turn the small FMS knob to select `Above Wpt' (AGL) or `MSL', and press the ENT key. `Above Wpt' uses the altitude of a destination airport. `MSL' lets you set a specific target altitude for any waypoint category: airport, VOR, NDB, intersection or user waypoint. Turn the small and large FMS knobs to select a distance from the target reference waypoint and press the ENT key. If the target altitude should occur at the target reference waypoint, enter a distance of zero. Turn the small FMS knob to select `Before' or `After', and press the ENT key. This setting designates whether the offset distance defines a point before you reach the target reference waypoint or after you reach the waypoint. When using a flight plan, the target reference waypoint itself can be specified from the waypoints contained in the flight plan. By default, the last waypoint in the flight plan is selected. To select a different waypoint, turn the small FMS knob to select the desired waypoint and press the ENT key. The default profile utilizes a 400 foot-perminute descent rate. [. . . ] B APPENDIX F OBSTACLE DATABASE Obstacle Color RED YELLOW GRAY Indication WARNING: Obstacle height is at or above 100 ft below the current aircraft altitude. CAUTION: Obstacle height is between 100 ft and 1000 ft below the current aircraft altitude. SAFE: Obstacle height is lower than 1000 ft below the current aircraft altitude. Lighted Obstacle (Height is less than 1000 ft AGL) Unlighted Obstacle (Height is greater than 1000 ft AGL) Lighted Obstacle (Height is greater than 1000 ft AGL) Unlighted Obstacle (Height is less than 1000 ft AGL) TERRAIN COLOR CHART Aircraft Altitude 100 ft Threshold 1000 ft AGL Figure F. 1 Terrain Color Chart 190-00629-00 Rev. [. . . ]