User manual GARMIN GBT 10 BENNETT TRIM TAB ADAPTER INSTALLATION AND CONFIGURATION INSTRUCTIONS

[. . . ] A Printed in Taiwan Determining an Installation Location When you are selecting a location to install the GBT 10 adapter, consider the following: · During installation, you connect the GBT 10 adapter to the Bennett TPI (or directly to the Bennett trim tab sensors), and to the NMEA 2000 network. Therefore: Choose a location that is within 173 in. (4. 4 m) of the Bennett TPI (or the Bennett trim tab sensors) to avoid splicing bare wires. Choose a location between the NMEA 2000 backbone and the Bennett TPI (or the Bennett trim tab sensors). [. . . ] Connect the NMEA 2000 connector on the GBT 10 adapter to the T-connector added in step 3. GBT10InstallationandConfigurationInstructions 5. (Optional) If the GBT 10 adapter cannot connect directly to the NMEA 2000 backbone, route a NMEA 2000 drop cable (not included) to the bottom of the T-connector added in step 3. Use a drop cable with a length up to 20 ft. Connect the drop cable to the T-connector and to the NMEA 2000 connector on the adapter. notiCe: If you have an existing NMEA 2000 network on your boat, it should already be connected to power. Do not connect an additional NMEA 2000 power cable to an existing NMEA 2000 network, because only one power source should be connected to a NMEA 2000 network. note: This section provides specific configuration information for the GBT 10 adapter using your compatible Garmin display device. To access the NMEA 2000 configuration menu on your display device, consult the documentation provided with your display device. Configuring the GBT 10 Adapter Calibrating the Trim Tab Position To use the GBT 10 adapter, you must calibrate the position of the trim tabs the adapter is associated with. note: If you only adjust your trim tabs within a limited range of motion on a regular basis, calibrate the GBT 10 adapter using your normal range instead of the full range. Only the calibrated range will be displayed on your chartplotter or marine instrument. 1. From the NMEA 2000 Devices list, select the GBT 10 device. Select an option: · For most Garmin chartplotters, select Review > Trim Tab Calibration. · For other Garmin marine devices, select Config > Trim Tab Calibration. Follow the on-screen instructions to calibrate the trim tab position. Configuring the GBT 10 Adapter if the Trim Tab Calibration Selection Is Not Displayed Depending on the version of software loaded on your Garmin marine instrument, the specific configuration options may not be displayed on the configuration screens. To calibrate the trim tab position if the menu option is not displayed: To use the GBT 10 adapter, you must calibrate the position of the trim tabs that the adapter is associated with. You can enter a minimum of two, and a maximum of sixteen, trim tab positions. For greater accuracy, enter more trim tab positions. 1. WhileviewingtheNMEA2000configurationmenu, selecttheGBT10device. Select Config > Generic Configuration. Enter the following command: "CALIBRATION=1" 4. Move both trim tabs to the highest position. When the trim tabs are in the highest position, they should be at or near 0% of their full range of motion. Enter the following command: "TRIMTABPOS=" 6. After the command, enter the percentage of the highest trim tab position as a whole number between 0 and 100, and select Done. [. . . ] Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements. [. . . ]