User manual GARMIN GNC 250

[. . . ] OWNER'S MANUAL & REFERENCE ACTV STBY GNC 250 CLR ENT CRSR SQ NRST RTE WPT NAV MSG GNC 250 's Guide Pilot ® TM INTRODUCTION Foreword Software Version 2. 06 or above © 1995 GARMIN International 9875 Widmer Road, Lenexa, KS 66215, USA Romsey House, Station Approach Romsey, Hampshire, UK S051 8DU All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of GARMIN. GARMINTM, GNC 250TM, Spell'N'FindTM, AutoLocateTM, MultiTrac8TM, GPSCOMTM and AutoStoreTM are trademarks of GARMIN and may only be used with permission. NavData® is a registered trademark of Jeppesen Sanderson, Inc. Information in this document is subject to change without notice. GARMIN reserves the right to change or improve their products and to make changes in the content of this material without obligation to notify any person or organization of such changes or improvements. All rights reserved. October 1995 190-00067-50 Rev. [. . . ] Warning: If you enter the overlap area you will only be informed of the nearest proximity waypoint. To remove a waypoint from the proximity waypoints page: 1. Press C twice, if necessary, to obtain a cursor in the GPS window. Proximity Alarm 2. Press \ to erase the name, and then E to delete. To scroll through the proximity waypoints list: 1. Rotate K with the flashing cursor inactive (or use O with the flashing cursor active) to scroll through the available proximity waypoints. The scrolling arrow prompt will indicate the direction to scroll to view additional waypoints, if available. 48 The third page available from the GNC 250's WPT key is the user waypoint list, which can be used to quickly scan, review, rename or delete user waypoints. To display the user waypoint list: 1. Press W and use O to display the user waypoint list. To scroll through the list, rotate K. REFERENCE WPT KEY RouteWaypointand User Copying List Closest Pt of Approach (CPA) SECTION 3 The total number of user waypoints is displayed at the top of the page, with user waypoints listed two at a time in alphabetical order. The scrolling arrow prompt, located at the top left of the page, will indicate which direction to scroll to view additional waypoints. The status of each waypoint, if applicable, will be displayed to the right of the identifier. A status will appear when it is the active-to waypoint, part of an active or stored route or a proximity waypoint. To edit, rename or delete waypoints, the cursor must highlight the desired waypoint. To highlight a waypoint: 1. Press C twice and use O to highlight the desired waypoint. Press E to obtain the waypoint position page. Edit the waypoint position as described on pages 45-46. Note: The active-to waypoint cannot be edited. Highlight the desired waypoint and press \. Use K and O to enter a new identifier for the waypoint. Press E on the confirmation page to change the name, or press \ to cancel. User Waypoint List SECTION 3 Waypoint Comments REFERENCE WPT KEY CPA Diagram The last page available through the GNC 250's WPT key is the waypoint comments page, which lists all waypoints that have a user comment. User comments may be added to 250 waypoints stored in the user or NavData® database, and allow you to note two lines of special information concerning a particular waypoint. To enter user comments: 1. Enter the waypoint identifier from any waypoint page (see page 35), and press C to remove the flashing cursor. [. . . ] - This message appears approximately 90 seconds prior to a turn that requires a bank angle in excess of 25 degrees in order to stay on course. Turn anticipation will not be provided for the turn. - Stored user data, including waypoints, routes and satellite orbital data have been lost due to a low memory battery or inadvertent master reset. - The microphone/headsets have been transmitting continuously for 35 seconds, and the transmitter has been disabled. [. . . ]