User manual GARMIN GPS 17HVS 2006 2010 GPS 17 INSTALLATION

[. . . ] Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www. garmin. com) for current updates and supplemental information concerning the use and operation of this and other Garmin products. Garmin® is a registered trademark of Garmin Ltd. [. . . ] Secure the bail mount to the surface with the fasteners. Slide the unit into the bail mount and tighten the mounting knobs. To install the Bail Mount and unit: Bail Mount Mounting knobs Bail mount 4 GPSMAP 2006C/2010C & GPS 17 INSTALLATION INSTRUCTIONS Flush Mount Tools · · · · · · · · · · Flush Mount Template Jig saw Masking tape Scissors Drill Drill bits--1/8" (3 mm) and 3/8" (6 mm) 1/16" (2 mm) Allen (Hex) wrench Sockets or wrenches Hammer Center punch Trim the Flush Mount Template and tape it in the location you want. Using the center punch, indent the center of each mounting hole location. Using an 1/8" (3 mm) drill bit, drill the four mounting holes. Using a 3/8" (6 mm) drill bit, drill a hole for a location to begin cutting the mounting surface. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a file and sandpaper to refine the size of the hole. There is only a small amount of clearance between the case molding and the mounting holes. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16" (2 mm) Allen wrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten as this may damage the mounting stud!The studs have a reusable thread-locking patch pre-applied from the factory. Place the unit in position in the cut-out of the mounting surface. Place washers over the mounting studs, then thread on one hex nut per mounting stud. Tighten all four until the unit is snug against the mounting surface. Install and tighten the second hex nut set on all four mounting studs to lock the first set in place. To flush mount the GPSMAP 2006C/2010C: 1. 5. Flush Mount TRIM TEMPLATE ALONG THIS LINE TO AID FITTING 230mm GPSMAP 2010/2010C/3010C CUT MOUNTING SURFACE ALONG INSIDE OF THIS LINE Be very careful when cutting this hole, there is only a small amount of clearance between the unit and the Mounting Hole. UNIT OUTLINE Flush Mounting the GPS 1. Trim the Flush Mount Template and tape in the desired location. Using the Center Punch, indent the center of each Mounting Hole location. Using an 1/8" (3mm) drill bit, drill the four Mounting Holes. (Drilling the mounting holes before cutting the hole for the unit will allow for an easier installation. ) 4. Using a 3/8" (6mm) drill bit, drill a hole for a location to begin cutting the mounting surface. [. . . ] A SWITCH OR RELAY CAN BE USED TO SELECT BETWEEN VISUAL AND AUDIBLE ALERTS, IF REQUIRED Diagram 1 - Basic Hook-up 8 GPSMAP 2006C/2010C & GPS 17 INSTALLATION INSTRUCTIONS + SHIP'S BATTERY 10-32 VOLTS - GARMIN GSD 20 SOUNDER MODULE (SEE GSD 20 INSTALL INSTRUCTIONS) (-) (-) (-) 4. A GARMIN SOUNDER UNIT (OTHER THAN GSD 20) CAN PROVIDE WATER DEPTH, WATER TEMPATURE, AND SPEED VIA NMEA DATA FOR DISPLAY ON THE GPSMAP 2006/2010. Diagram 2 - Complete Interface GPSMAP 2006C/2010C & GPS 17 9 INSTALLATION INSTRUCTIONS Final Wiring Connection Once all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2006/2010. The 5-pin port on the right side is intended for future interfacing features and does not require connection at this time. With power applied to the circuit, you may test the installation by pressing the POWER Manual for steps on initializing the receiver. [. . . ]