Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual GARMIN GPS 158I. We hope that this GARMIN GPS 158I user guide will be useful to you.
Lastmanuals help download the user guide GARMIN GPS 158I.
Detailed instructions for use are in the User's Guide.
[. . . ] Measuring Distance
You can measure the distance and bearing between any two points on the map. 2 Move the map pointer to the first point. 4 Move the map pointer to the second point. The distance and bearing from the first point to the second point appear in the data field at the top of the map.
➋
Marking a Waypoint
➌
➍
➎
4
You can mark up to 3000 waypoints. [. . . ] 6 Using the appropriate drill bit for the hardware, drill the three pilot holes. 7 If you plan to run the power and transducer cables from under the mounting
surface, use a 5/8 in. (16 mm) drill bit to drill a hole through the mounting surface at the location you marked in step 5.
Fastening the Swivel Mount without the Cables Installed in the Mount
➋
Follow these steps only if you do not need to run the cables through the mounting surface and the swivel mount. 1 Place the base ➊ on the mounting surface, and fasten it using the appropriate screws or bolts ➋.
➋ ➌ ➍ ➊
2 Place the swivel mount on the base, and replace the 10 mm M6×1 Phillips
screw. 3 Seal the cable pass-through holes with marine sealant.
3 If you plan to route the cables from under the mounting surface, orient the base so the pass-through holes ➍ face the desired direction. 4 Using the base as a template, mark the pilot hole locations ➎.
➎ ➏
10
GPS 158 Owner’s Manual
Fastening the Swivel Mount with the Cables Installed in the Mount
Follow these steps only if you need to run the cables through the mounting surface and the swivel mount. 1 If you are installing the cables in the mount, feed the cables through the 5/8 in. (16 mm) center hole you drilled when preparing the base. 2 Place the base on the mounting surface. 3 Route the cables through the cable pass-through holes. 4 Loosely fasten the base using the appropriate screws or bolts. 5 Place the swivel mount on the base, but do not fasten it. 6 Place the cradle into the swivel mount (page 11). 7 Pull out enough slack from the power and transducer cables so the mount can fully swivel to the desired positions when the cables are connected. 8 Remove the cradle and the swivel mount from the base. (16 mm) center hole and to the cable passthrough holes. 10 Securely fasten the base with the appropriate screws or bolts. 11 Place the swivel mount on the base, and fasten it using the included 10 mm M6×1 Phillips screw.
➋
➊ ➌
2 Tilt the mount to the desired viewing angle. 3 Press the locking arm down.
Installing the Cradle in the Swivel Mount
Installing the Cables and Connectors
Wiring to Power 1 Route the power cable from the swivel mount to the boat battery or fuse block. 2 Connect the red wire to the positive terminal on the battery or fuse block, and
connect the black wire to the negative terminal. If necessary, extend the wires using 20 AWG or larger wire.
1 With the locking arm ➊ in the upward position, place the cradle ➋ into the swivel mount ➌.
GPS 158 Owner’s Manual
11
Connecting the Cable and Placing the Device in the Cradle 1 Compare the divot ➊ on the cable connector to the keying on 2 3 4 5
the cradle port. Push the power cable connector into the power port until it rests firmly in the port. [. . . ] Online auction confirmations are not accepted for warranty verification. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace missing components from any package purchased through an online auction. International Purchases: A separate warranty may be provided by international distributors for devices purchased outside the United States depending on the country. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GARMIN GPS 158I
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual GARMIN GPS 158I will begin.