User manual GARMIN GPS 165 TSO PILOT'S GUIDE

[. . . ] OWNER'S MANUAL & REFERENCE MSG RTE NRST WPT SET NAV CLR CRSR ENT GPS 165TSO Pilot's Guide ® INTRODUCTION Foreword This manual is written for software versions 3. 06 or above, and is not suitable for earlier software versions. © 1995 GARMIN International 9875 Widmer Road, Lenexa, KS 66215, USA GARMINTM, GPS 165TSOTM, AutoLocateTM, MultiTrac8TM, Spell'N'FindTM and AutoStoreTM are trademarks of GARMIN International and may only be used with permission. JeppesenTM and NavData® are registered trademarks of Jeppesen Sandersen and are used with permission. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording for any purpose without the express written permission of GARMIN Corporation. Information in this document is subject to change without notice. GARMIN reserves the right to change or improve their products and to make changes in the content without obligation to notify any person or organization of such changes or improvements. April 1995 190-00066-00 Rev. [. . . ] Rotate K with the flashing cursor inactive (or O with the cursor active). DIRECT-TO & ROUTE NAV Flying the Active Route USING THE ACTIVE ROUTE PAGE The GPS 165's active route page provides a working list of the route you are navigating, allowing you to view all route waypoints, along with distance, and timing or desired track information. The scrolling arrow prompt to the left of the route waypoint list indicates which way to scroll to view additional route waypoints. The active route page can also be used to manually select your next `active to' destination, which allows you to fly the route out of sequence without modifying it. The GPS 165 will resume navigation of the remainder of the route in sequence once you arrive at the selected waypoint. The active leg identifiers field, located at the top left of the page, displays the waypoint identifiers of the route leg you are currently navigating. The first waypoint identifier displayed is the `active from' waypoint. The second waypoint is the `active to' waypoint. The line connecting these waypoints is known as the `active leg'. If you are navigating a direct-to, the field will display the destination only. 57 DIRECT-TO & ROUTE NAV Adding Active Route Waypoints The `cum or leg' field can be selected to display cumulative distance and ete/eta or the distance and ete/eta for each individual route leg. If cumulative is selected, the first leg's distance will be displayed, while the second leg will represent the first leg's distance plus the second leg, and so on. This also applies to the ete/eta field, which may also be configured to display the desired track (dtk) for each leg, regardless of the cumulative or leg selection. To change the leg and ete/eta fields: 1. With the flashing cursor active, rotate O to highlight the field you want to change. Rotate K to select the desired setting and press C. Active route page with desired track displayed. The active route page may also be used to create a new route or edit the route you are currently navigating (approach, SID or STAR waypoints cannot be edited), and provides a fast method of selecting any route waypoint as your next destination waypoint without modifying the active route. If you are editing the active route and want to save it in its original form, copy it to an open storage route before editing. To add waypoints to the active route: Adding a waypoint to the active route. 1. Press C, if necessary, to activate the cursor. Use O to highlight the first blank waypoint field or highlight the waypoint you would like to add the new waypoint BEFORE. Use K and O to enter the new waypoint identifier. Press E. Confirming the new route waypoint. 4. The cursor will automatically move to the next waypoint field, and the remaining route waypoints (if any are present) will move down the list accordingly. 58 To delete a waypoint from the active route: 1. Press C, if necessary, to activate the cursor. Use O to highlight the waypoint you would like to delete from the active route. The next route waypoint (if available) will move up to take the position of the deleted waypoint. DIRECT-TO & ROUTE NAV On-Route Direct-To The active route page also allows you to select your next destination waypoint manually from the active route waypoint list and resume the remainder of the route in sequence. This procedure, referred to as an `on-route' direct-to, allows the pilot to fly the active route in a different sequence without editing the active route, approach, SID or STAR itself. [. . . ] If you are in a missed approach situation, and would like to return the CDI to the 1 nm scale, you may deactivate the approach by releasing the GPS APPR switch from the ARM position. Why does my CDI not respond like a VOR when the GPS SEQ switch is set to HOLD?Unlike a VOR, the CDI scale used on GPS equipment is based on the cross-track distance to the desired course, not an angular relationship to the destination. Therefore, the CDI deflection on the GPS will be consistent regardless of the distance to the destination, and will not become less sensitive when you are further away from the destination. [. . . ]