User manual GARMIN VIB 10 INSTALLATION GUIDE

[. . . ] Garmin disclaims all liability for any loss, injury, or damage resulting from the installation activities. · Do not open the VIB or loosen the case screws. Doing so will void the warranty. Caution: The VIB speaker outputs are differential. [. . . ] The Fakra plug locks firmly in place. Seethe"VIB 11 Antenna Connections"drawingsontheback. ConnecttheFakraconnectoroftheadaptercabletotheAnt. Outconnector oftheVIB11. Connecttheappropriateadaptercabletothestereo'santenna connector. Seethe"VIB 11 Antenna Connections"drawingsontheback. notE: To test the installation, turn on the vehicle's stereo. If you can hear sound from an FM radio station, you have properly connected the VIB 11. You will need a vehicle-specific automotive accessory mount bracket that has a standard AMPS 4-hole pattern. Automotive accessory mount brackets are available from many locations such as RAM (www. ram-mount. com), Panavise (www. panavise. com) and Pro. Fit (www. pro-fit-intl. com) Step5:RoutetheGPSPowerCable Step1:AttachtheMount Using the four included screws, attach the included mount to the third-party mount bracket. The ball socket should face toward the vehicle's seats. Connect the GPS navigator wiring harness to the To PND connector on the VIB. Route the cable to reach the GPS navigator. Attempt to minimize the cable's visibility by routing it through an existing opening in the glove box, trim panel, or air vent. Step2:InstalltheThird-PartyMountBracket Step6:MounttheVIB Follow the mount bracket manufacturer's instructions to install the mount bracket. InstallInGtheVIB10/11 Step1:PreparetheDashboard Test the stereo to ensure that it receives FM Stereo signals and that the antenna functions properly (VIB 11 only). Remove the trim panel or other parts of the dashboard. Detach the antenna cable and wiring harness. Antenna cable Wiring harness After all the wiring connections are made and the GPS power cable is properly routed, use screws or wire ties to secure the VIB behind the stereo. Step7:ReplaceDashboard When finished, replace the stereo and all parts of the dashboard to their original locations. Plug the power cable from the VIB into the power connector on the back of the GPS navigator or GPS navigator's cradle. Align the ball on the mount with the socket on the GPS navigator or GPS navigator's cradle. Snap the GPS navigator or cradle onto the ball socket. Refer to the GPS navigator's documentation for more information. notE: To operate the GPS navigator with the VIB, you need to updated the GPS navigator's software. See the VIB Reference Guide or GPS navigator's documentation for more information. MountInGtheGpsnaVIGator Step2:ConnecttheSpeakerandPowerWires The VIB wiring harness uses the standard EIA color code. Refer to the wiring diagram on the back. Connect the bare ends of the 24-pin connector harness to the vehicle power, stereo, and speakers. [. . . ] · Do not expose the unit to water or other liquids. · Do not install the unit where it will be exposed to direct sunlight, excessive heat or humidity, or dust. Stereo 12 VDC Ground Ignition notE: There may be additional signals from the stereo that are not shown on this diagram. Any such signals should be connected directly back to the stereo. VIB10/11WiringDiagram Reverse In Mute Out Ground In 1 2 3 4 5 6 7 8 9 Pink Light Green Black Black Yellow Yellow Red Tan Green/Black Green Purple/Black Purple White/Black White Grey/Black Grey Optional Optional Vehicle Ground 12 VDC Ignition Ground for Low-level output; Float for High-level output VehicleSpeakers LR (-) LR (+) RR (-) RR (+) LF (-) LF (+) RF (-) RF (+) StereoSystemOut LR (-) LR (+) RR (-) RR (+) LF (-) LF (+) RF (-) RF (+) ToAntennaAdapterCable 2 VIB10/1124-Pin Connector 24 Ground In 12 VDC In 12 VDC In Ignition Output Level 1 23 VIB10/1124-PinConnector LR (-) Out LR (+) Out 10 RR (-) Out 11 RR (+) Out 12 LF (-) Out 13 LF (+) Out 14 RF (-) Out 15 RF (+) Out 16 Video In VIB10/11Connectors To Stereo/ vehicle wiring (24-pin connector) To PND (GPS navigator) Ant Out to stereo's antenna connector (VIB 11 Only) Ant In from vehicle's antenna (VIB 11 Only) LR (-) In 17 Audio Out (optional) LR (+) In 18 RR (-) In 19 RR (+) In 20 LF (-) In 21 LF (+) In 22 RF (-) In 23 RF (+) In 24 Green/Black Green Purple/Black Purple White/Black White Grey/Black Grey VIB11AntennaConnections ToStereoAdapterCable adapter to stereo Fakra to VIB 11 Ant. [. . . ]