User manual GARY FISHER CYBER COMPUTER

[. . . ] Watching your bicycle computer makes it difficult to see upcoming obstacles. Awareness of potential road, trial, or traffic problems should be your main concern. Speedometer (miles or kilometers) (SPD) (M/hr or KM/hr) Tells you your instantaneous speed. Accurate to 0. 1 mph or Kmph SPD/STP Cumulative Odometer (ODO) Stores your total mileage for the year in tenths of a mile or km from 0 to 9999. 9 and in full miles or km from 10, 000 to 99, 999 SPD/ODO Automatic Ride Time Stopwatch (STP) Stopwatch that starts and stops when your wheel is turning. [. . . ] To remove the computer from the bracket, place your thumb against the back of the mounting bracket and pull the computer toward you with your index finger. 5 Setting the Clock, Thermometer and Miles or Kilometers 1. In the SPD/STP screen, press and hold the MODE key for 2 seconds. The screen will clear and Mi, F and 12 will appear indicating the American calibration settings. Press the START/STOP key to change to the Metric settings if desired, or press the MODE key to set screen and advance to Adjusting the Clock 4. The Hours digits will appear and begin to flash. Advance the Hours by pressing the START/STOP key. NOTE: Holding the START/STOP key will fast advance the digits. Press the MODE key to set the screen and advance to setting the Minutes in the same manner as Hours. Press the MODE key one final time to set the screen and return to the main screen . Wheel Size Setting The wheel size setting number is equal to the distance, in millimeters, that your front wheel travels during one complete revolution. Each time the wheel magnet passes the sensor unit on your fork, the sensor sends an impulse to the computer telling it that your wheel has completed one revolution. The computer calculates this distance vs. time to give you accurate readings for the various modes. Determining Wheel Size Setting There are three methods for determining the wheel size setting. For the most accurate computer readings, it is best to measure the actual distance that your wheel travels in one complete revolution. Method One: Wheel Roll Out Method Two: Measure wheel radius (including tire) in mm and multiply by 6. 2832=Wheel setting number. Method Three: Refer to the following chart and input the number that corresponds to your tire size. (Note: Actual size of two similarly marked tires from different manufactures can vary significantly, making this method the least accurate. ) WHEEL SIZE CHART Wheel/Tire Size Wheel Size Setting in mm 26 x 1. 0 ATB . . 2110 The Cyber is equipped with 3 buttons that conrol the functions of the unit: 1. MODE Changes the Main Screens of the Cyber 2. WORKOUT WINDOW Enters and Exit's the Workout Window 3. START/STOP Starts and stops the Stopwatch in the Workout Window and adjusts the digits when setting he Clock, Wheel Size and Odometers. PROGRAMMING YOUR FISHER CYBER CYCLE COMPUTER We will now begin to program the features of he Cyber. [. . . ] Pressing the START/STOP key for 2 seconds in the WORKOUT WINDOW SPD/STP screen will reset only the WORKOUT WINDOW functions and will not affect the Normal Operating functions. Resetting Maximum Speed ­Just as in the Normal operating mode. If you are doing sprint workouts, the Workout Window maximum speed of the Cyber can be reset independent of the other WORKOUT WINDOW functions by pressing and holding the MODE key for two seconds while in the SPD/MAX screen. 8 9 Desired Function Advance Digits While Programming Set Digits While Programming Escape From Programming Mode Set Clock, Thermometer and Units Set Wheel Size Main Programmable ODO Reset All Functions Reset Main Max Speed Only Enter Workout Window Workout Window Programmable ODO Start Workout Window Reset only Workout Window Functions Reset only Workout Window Max Speed Which Key to Press Start/Stop Mode Mode for 1 Sec Mode for 2 Sec Mode for 2 Sec Automatic at end of Wheel Size Setting Start/Stop for 2 Sec Mode for 2 Sec Workout window Mode for 2 sec Start Stop while in Workout Window Start/Stop for 2 Sec Mode for 2 Sec Notes Hold for Fast Advance In SPD/STP Screen In SPD/ODO Screen In SPD/STP Screen In SPD/MAX Screen In any Screen In Workout Window SPD/ODO Screen Initial start only, subsequent starts and stops are automatic In Workout Window SPD/STP Screen In Workout Window SPD/MAX Screen TROUBLESHOOTING GUIDE Problem No speedometer reading Display Readout Fades Display shows irregular figures MX display reads 99. 5 Slow display response Black display Solution Check for proper magnet sensor alignment. Check computer to make sure it is snapped firmly into the bracket. [. . . ]