User manual GAS GAS TXT BOY 2006

[. . . ] This symbol introduces special warnings to avoid damaging your motorbike. Should these warnings not be heeded, the guarantee may be automatically invalidated. These are the instructions necessary to ensure good use of the control and adjustment mechanisms, in addition to the correct conservation and maintenance of the motorbike, to guarantee maximum satisfaction when riding. The aim of this Manual is to help the user minimise or avoid possible damage to people, property, the environment, and naturally to his/her new motorbike. [. . . ] - Remove the filler cap and fill with oil (450 cc). - See Quick Guide to Maintenance, page 8. Warning: Do not pour used oil down the drain. C 11 A Warning: Use the recommended oil. - See Quick Guide to Maintenance, page 8. - Replace filler cap and tighten. -14- 7 7 Clutch system- Checking The clutch system is hydraulic. Regularly check the level of fluid through the transparent window A on the tank. - Position the lever so that the tank cover is horizontal. - The level is correct if it falls within the upper half of the transparent window. See Quick Guide to Maintenance, page 8. C 13 7 A 12 A Clutch system - Bleeding If the system has been dismounted for repair, or if faults are detected in the clutch system, the air in the hydraulic circuit can be removed using the bleeder A. Once the air has been removed from the system, replace the rubber cap on the bleeder to prevent dirt from entering the system. Warning: Do not pour used oil down the drain. C 7 -15- as follows: - Undo the bolts shown by the arrow and remove the fuel tank cover and the rear seat unit. - Carefully lift and remove the fuel tank. Warning: If the motorcycle has just been used, wait a few minutes before opening the radiator cap. - Turn cap A in an anti-clockwise direction until it is loosened. - Wait a few seconds, then push the cap downwards, finish the turn in the same direction and remove the cap. - The level of coolant should be at the lower edge of the filler neck of the radiator, below the position of the cap seal. If this is not the case, top up with coolant. Warning: Only use coolant suited to light-alloy engines, with antifreeze protection of up to 30 ºC. -16- 7 A C Coolant system ­ Checking/topping up To reach the radiator cap, proceed 14 7 Carburettor - Adjusting throttle cable The throttle lever cable should have a free play of between 2 to 3 mm. - Raise the dust guard A on the throttle lever cable. - Turning the threaded terminal B to the right increases the play of the cable, and turning it to the left reduces the play. C A A B 15 16 B A Carburettor ­ Adjusting the idle speed The carburettor has an idle adjusting screw A, which acts on the opening of the carburettor throttle curtain, and an air adjusting screw for the low system B, which controls the proportion of air in the air/fuel mixture. 7 C -17- 17 _ 0. 6 ~ 0. 7 mm 7 C Spark plugs - Inspecting The electrode separation is from 0. 6 to 0. 7 mm. Air Filter - Cleaning A clean air filter not only improves engine performance but also prolongs its useful life. It should therefore be cleaned regularly. To reach the air filter, proceed as follows: - Undo the bolts shown by the arrows, and remove the rear seat unit. [. . . ] The GG authorised dealer, to whom the making good of the defects has been entrusted, is not authorised to make any declarations that are binding on GG. 2. - In case of doubt regarding the existence of a defect, or a visual or material inspection is required, GG reserves the right to demand the return of the parts which are the object of a claim under Warranty, or to arrange an inspection of the defect by an expert from GG. Any additional obligations arising out of guarantees on parts replaced free of charge, or any other service rendered free of charge, are excluded from the effects of this present warranty. The Warranty on parts replaced within the Warranty Period will end at the expiry date for the Warranty Period of the product concerned. [. . . ]