Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual GE SECURITY NX-148. We hope that this GE SECURITY NX-148 user guide will be useful to you.
Lastmanuals help download the user guide GE SECURITY NX-148.
Manual abstract: user guide GE SECURITY NX-148REV E
Detailed instructions for use are in the User's Guide.
[. . . ] 5 MAKING YOUR SYSTEM READY TO ARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ARMING YOUR SYSTEM IN THE "STAY" MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 USING THE QUICK ARM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 DISARMING YOUR SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The LCD Screen will display the zone status.
Step 2 Use the up and down scroll keys to browse through the descriptions. The LCD Screen will display the list of all zones in sequential order by zone number. Step 3 Press [#] to exit this function.
SETTING THE KEYPAD TONE Step 1 Press U 0 . Keypad is now in the "Adjust Tone" mode.
Step 2 Press the x up scroll key located on the right side of the display to adjust the keypad sounder to higher tones.
5DLVHWRQH /RZHUWRQH
Step 3 Press the y down scroll key to adjust the keypad sounder to lower tones. Step 4 When the desired tone is reached, press # to set this tone and exit from the "Adjust Tone" mode.
VIEW ALARM MEMORY Step 1 Press U alarm. 3 to display the zone(s) on the keypad that created the last
Step 2 The LCD Screen will display the zone description for those zones. Step 3 Press [#] to exit the alarm memory.
$ODUP0HPRU\ =21(
TEST FUNCTION (Optional, if programmed) If programmed, this function will perform a battery test, communicator test, and/or a siren test. No alarms will be sent, and no reports will be sent unless a communicator test is performed, in which case a test signal will be sent. The test will be performed as programmed.
Step 2 If the siren test is performed, enter a user code to silence the siren.
11
DISPLAY TEST FUNCTION This function will perform a test of the LCD display. The test will be performed and all of the display pixels and LED indicators will flash until another key is pressed. Step 2 Press any key to end the test.
LIGHT CONTROL FOR X-10 DEVICES (Optional, if programmed) This menu allows you to control up to ten X-10 devices from each keypad. The LCD Screen will now prompt for a code.
Enter [master code]. The LCD Screen will prompt for a user number. Enter the 2-digit (applies to NX4/6/8) or 3-digit (applies to NX8E) user number. Always use leading zeros when necessary, i. e. The LCD will now prompt you for the attributes in the following chart.
13
PROMPT Outputs used?Output 1?
DO NOT CHANGE THIS SEGMENT!(These are for use by a professional installer only. ) 0=No 1=Yes Your keypress will apply to the user code you entered in Step 3. If these messages appear on the LCD screen, press the [U] key until you return to the prompt for the user code or until you exit this adjust mode.
Step 4
NOTE: The LCD will now display all of the partitions to which this user has access. If you wish to remove a partition, press the partition number on the keypad, and the display will mark that partition with a (-) hyphen indicating access has been removed. If you wish to re-establish user access to the partition, press the partition number again. The LCD will then prompt you for the next user code. [. . . ] Communication of a signal has failed (log only event). A zone "Walk-Test" mode has been activated. The first zone of a cross zone has been tripped (log only). An expansion module created an undefined event. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GE SECURITY NX-148
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual GE SECURITY NX-148 will begin.
