User manual GEMINI 7502

[. . . ] Declaration of conformity to type Dichiarazione di conformità I hereby declare that the product Qui di seguito si dichiarache il prodotto 7208E - 7218E (Name of product, type or model, batch or serial number) (nome del prodotto o modello, categoria o numero di serie) Is conform to all relevant essential requirements of the R&TTE-directive 1995/5/EC, issued March 9, 1999. According to Annex IV of the R&TTE directive. The following standards and essential radio test suites published in the "Official Journal" of the European Communities, have been used to demonstrate the conformity of the product: Product in class 1 frequency identification Electrical safety: Radio and spectrum engineering parameters: Electromagnetic Compatibility EMC: Certificate of conformity: Expert Opinion: En 60950-2000 En 300220-1/1997 ETS 300683 : 1997 E811117M-CC E811117M-EO Soddisfa tutti i requisiti applicabili alla tipologia del prodotto e richiesti dalla regolamentazione delle telecomunicazioni secondo direttiva R&TTE5/9 allegato IV tramite l'utilizzo delle norme pubblicate nella gazzetta ufficiale della Comunità Europea: Prodotto in frequenza identificata come classe 1 Sicurezza elettrica: Radio e parametri di trasmissione: Compatibilià elettromagnetica EMC: Certificato di conformità: Certificato dell'esperto: En 60950-2000 En 300220-1 /1997 ETS 300683 : 1997 E811117M-CC E811117M-EO A, B, D, DK, F, FR, GR, IR, I, L , NL, P, SP, S, UK GEMINI TRADING S. R. L. 7503 7502 7501 The product can be used in the following European Countries: Il prodotto può essere immesso nei seguenti Stati Europei: Company responsible for placing on the market: Società responsabile per l'immissione nel mercato: Address: Indirizzo: Point of contact: Persona di contatto: Via Luigi Galvani 12 - 21020 BODIO LOMNAGO (VA) - ITALY Andrea Rossi - Tel. +39 0332943211 - e-mail: a. rossi@gemini-alarm. com Bodio Lomnago - 19/09/2003 (Place, date) - (Luogo, data) For all EU countries (Signature) - (Firma) Wiring diagram art. 7503 ALARMSYSTEMS Push-button 2 Push-button 1 Electronic key 7503 MadeinItaly ALARMSYSTEMS MadeinItaly 7059 5123 AERIAL Do not tamper! Green/Black Brown Pink YELLOW-BLUE RED-BLUE YELLOW-GREY RED-GREY YELLOW-BROWN RED-BROWN See locks diagrams Red Black Green Brown 15A BLACK marked R Battery 12 Volt BLACK marked M BLACK marked VM EARTH Fuses not supplied 5A Door pushbutton ORANGE ORANGE BLACK marked V 5A Turn indicators Bonnet pushbutton BLACK marked V Fuses not supplied BLACK marked H BLACK marked H Boot pushbutton 8A MAX ! [. . . ] OPENING A DOOR OR STARTING THE CAR) within approx. The function prevents the vehicle from being left unprotected in cases where, after the activation of 2) While the status LED is ON, press key 1 on the remote, the LED will turn off at once, reflecting the activation of the GARAGE function. To deactivate the GARAGE function, it is sufficient to connect the alarm system with the remote. Using the electronic key, to turn on and off the alarm system, does not reset the GARAGE function. DEACTIVATING THE ALARM: In this situation it is necessary for the user to get into the car to cause an alarm condition. At the end of the alarm cycle (lasting approx. 30"), the system will be in the neutral time between successive alarms (duration approx. 5" ­ status LED emitting a continuous light). To activate the release procedure during this phase it is necessary to turn the ignition key to the ON position and then to the OFF position within approx. At the end of this operation, the status LED will turn off and the release procedure by means of the PIN-CODE can be started. ATTENTION: if the ignition key remains in the ON position for more than three seconds during the neutral time between alarms, the system will interpret this situation as an attempted theft and therefore a new visual/audio alarm cycle will start. Once the release procedure has begun (i. e. when the ignition key returns to the OFF position), there will be a pause of approx. 4 seconds, after which the status LED will emit an initial sequence of 9 flashes according to the following timing scheme: 0. 5" ON ­ 1" OFF. Each of these flashes can represent the number of the first digit of the release PIN-CODE. In other words: 1st FLASH Ü NUMBER OF 1st DIGIT 2nd FLASH Ü NUMBER OF 2nd DIGIT 3rd FLASH Ü NUMBER OF 3rd DIGIT 4th FLASH Ü NUMBER OF 4th DIGIT 5th FLASH Ü NUMBER OF 5th DIGIT 6th FLASH Ü NUMBER OF 6th DIGIT 7th FLASH Ü NUMBER OF 7th DIGIT 8th FLASH Ü VALUE OF DIGIT 8 9th FLASH Ü VALUE OF DIGIT 9 To exemplify: let us suppose the PIN-CODE for the system is 4-3-2-1. To enter the first digit (4), turn the ignition key to the ON position for at least one second during the fourth flash of the status LED, or press the pushbutton on the LED (if LED art. This way the first digit (4) will be entered and after a pause of four seconds a new sequence of nine flashes of the status LED will occur and it will be possible to enter the second digit of the PIN-CODE (3). As in the procedure to enter the first digit, all you have to do to enter the second digit is turn the ignition key to the ON position for at least one second during the third flash of the status LED or press the pushbutton on the LED (if LED art. And so on for the remaining two digits (2 and 1). After entering the fourth digit, the alarm system will be released / deactivated and the set visual signals will be emitted. Release by means of the PIN-CODE deactivates the ANTI-DISTRACTION and PASSIVE ACTIVATION OF THE ENGINE IMMOBILIZER functions. These functions will be reset upon the first system activation by remote. [. . . ] SENSITIVITY ADJUSTMENT The 7059 module has a TRIMMER for adjusting sensitivity from a minimum value (not ZERO) to a maximum value. Calibration is facilitated by the presence of a red LED emitting a continuous light for 4 seconds every time there is an interference in the module's protection radius. (NOTE: between one alarm signal and the next, at least four seconds must pass after the LED turns off). Adjust the TRIMMER to the maximum sensitivity position (all the way clockwise). [. . . ]